HCE2-SA-2026-0002 Important HCE 2.0 Security Fix(es): In the Linux kernel, the following vulnerability has been resolved: fbdev: Add bounds checking in bit_putcs to fix vmalloc-out-of-bounds Add bounds checking to prevent writes past framebuffer boundaries when rendering text near screen edges. Return early if the Y position is off-screen and clip image height to screen boundary. Break from the rendering loop if the X position is off-screen. When clipping image width to fit the screen, update the character count to match the clipped width to prevent buffer size mismatches. Without the character count update, bit_putcs_aligned and bit_putcs_unaligned receive mismatched parameters where the buffer is allocated for the clipped width but cnt reflects the original larger count, causing out-of-bounds writes. (CVE-2025-40304) In the Linux kernel, the following vulnerability has been resolved: xfs: do not propagate ENODATA disk errors into xattr code ENODATA (aka ENOATTR) has a very specific meaning in the xfs xattr code; namely, that the requested attribute name could not be found. However, a medium error from disk may also return ENODATA. At best, this medium error may escape to userspace as "attribute not found" when in fact it_x27;s an IO (disk) error. At worst, we may oops in xfs_attr_leaf_get() when we do: error = xfs_attr_leaf_hasname(args, &bp); if (error == -ENOATTR) { xfs_trans_brelse(args->trans, bp); return error; } because an ENODATA/ENOATTR error from disk leaves us with a null bp, and the xfs_trans_brelse will then null-deref it. As discussed on the list, we really need to modify the lower level IO functions to trap all disk errors and ensure that we don_x27;t let unique errors like this leak up into higher xfs functions - many like this should be remapped to EIO. However, this patch directly addresses a reported bug in the xattr code, and should be safe to backport to stable kernels. A larger-scope patch to handle more unique errors at lower levels can follow later. (Note, prior to 07120f1abdff we did not oops, but we did return the wrong error code to userspace.) (CVE-2025-39835) In the Linux kernel, the following vulnerability has been resolved: bpf: Fix issue in verifying allow_ptr_leaks After we converted the capabilities of our networking-bpf program from cap_sys_admin to cap_net_admin+cap_bpf, our networking-bpf program failed to start. Because it failed the bpf verifier, and the error log is "R3 pointer comparison prohibited". A simple reproducer as follows, SEC("cls-ingress") int ingress(struct __sk_buff *skb) { struct iphdr *iph = (void *)(long)skb->data + sizeof(struct ethhdr); if ((long)(iph + 1) > (long)skb->data_end) return TC_ACT_STOLEN; return TC_ACT_OK; } Per discussion with Yonghong and Alexei [1], comparison of two packet pointers is not a pointer leak. This patch fixes it. Our local kernel is 6.1.y and we expect this fix to be backported to 6.1.y, so stable is CCed. [1]. https://lore.kernel.org/bpf/CAADnVQ+Nmspr7Si+pxWn8zkE7hX-7s93ugwC+94aXSy4uQ9vBg@mail.gmail.com/ (CVE-2023-54181) In the Linux kernel, the following vulnerability has been resolved: fuse: fix livelock in synchronous file put from fuseblk workers I observed a hang when running generic/323 against a fuseblk server. This test opens a file, initiates a lot of AIO writes to that file descriptor, and closes the file descriptor before the writes complete. Unsurprisingly, the AIO exerciser threads are mostly stuck waiting for responses from the fuseblk server: # cat /proc/372265/task/372313/stack [<0>] request_wait_answer+0x1fe/0x2a0 [fuse] [<0>] __fuse_simple_request+0xd3/0x2b0 [fuse] [<0>] fuse_do_getattr+0xfc/0x1f0 [fuse] [<0>] fuse_file_read_iter+0xbe/0x1c0 [fuse] [<0>] aio_read+0x130/0x1e0 [<0>] io_submit_one+0x542/0x860 [<0>] __x64_sys_io_submit+0x98/0x1a0 [<0>] do_syscall_64+0x37/0xf0 [<0>] entry_SYSCALL_64_after_hwframe+0x4b/0x53 But the /weird/ part is that the fuseblk server threads are waiting for responses from itself: # cat /proc/372210/task/372232/stack [<0>] request_wait_answer+0x1fe/0x2a0 [fuse] [<0>] __fuse_simple_request+0xd3/0x2b0 [fuse] [<0>] fuse_file_put+0x9a/0xd0 [fuse] [<0>] fuse_release+0x36/0x50 [fuse] [<0>] __fput+0xec/0x2b0 [<0>] task_work_run+0x55/0x90 [<0>] syscall_exit_to_user_mode+0xe9/0x100 [<0>] do_syscall_64+0x43/0xf0 [<0>] entry_SYSCALL_64_after_hwframe+0x4b/0x53 The fuseblk server is fuse2fs so there_x27;s nothing all that exciting in the server itself. So why is the fuse server calling fuse_file_put? The commit message for the fstest sheds some light on that: "By closing the file descriptor before calling io_destroy, you pretty much guarantee that the last put on the ioctx will be done in interrupt context (during I/O completion). Aha. AIO fgets a new struct file from the fd when it queues the ioctx. The completion of the FUSE_WRITE command from userspace causes the fuse server to call the AIO completion function. The completion puts the struct file, queuing a delayed fput to the fuse server task. When the fuse server task returns to userspace, it has to run the delayed fput, which in the case of a fuseblk server, it does synchronously. Sending the FUSE_RELEASE command sychronously from fuse server threads is a bad idea because a client program can initiate enough simultaneous AIOs such that all the fuse server threads end up in delayed_fput, and now there aren_x27;t any threads left to handle the queued fuse commands. Fix this by only using asynchronous fputs when closing files, and leave a comment explaining why. (CVE-2025-40220) In the Linux kernel, the following vulnerability has been resolved: ipv6: use RCU in ip6_output() Use RCU in ip6_output() in order to use dst_dev_rcu() to prevent possible UAF. We can remove rcu_read_lock()/rcu_read_unlock() pairs from ip6_finish_output2(). (CVE-2025-40158) In the Linux kernel, the following vulnerability has been resolved: usb: uas: fix urb unmapping issue when the uas device is remove during ongoing data transfer When a UAS device is unplugged during data transfer, there is a probability of a system panic occurring. The root cause is an access to an invalid memory address during URB callback handling. Specifically, this happens when the dma_direct_unmap_sg() function is called within the usb_hcd_unmap_urb_for_dma() interface, but the sg->dma_address field is 0 and the sg data structure has already been freed. The SCSI driver sends transfer commands by invoking uas_queuecommand_lck() in uas.c, using the uas_submit_urbs() function to submit requests to USB. Within the uas_submit_urbs() implementation, three URBs (sense_urb, data_urb, and cmd_urb) are sequentially submitted. Device removal may occur at any point during uas_submit_urbs execution, which may result in URB submission failure. However, some URBs might have been successfully submitted before the failure, and uas_submit_urbs will return the -ENODEV error code in this case. The current error handling directly calls scsi_done(). In the SCSI driver, this eventually triggers scsi_complete() to invoke scsi_end_request() for releasing the sgtable. The successfully submitted URBs, when being unlinked to giveback, call usb_hcd_unmap_urb_for_dma() in hcd.c, leading to exceptions during sg unmapping operations since the sg data structure has already been freed. This patch modifies the error condition check in the uas_submit_urbs() function. When a UAS device is removed but one or more URBs have already been successfully submitted to USB, it avoids immediately invoking scsi_done() and save the cmnd to devinfo->cmnd array. If the successfully submitted URBs is completed before devinfo->resetting being set, then the scsi_done() function will be called within uas_try_complete() after all pending URB operations are finalized. Otherwise, the scsi_done() function will be called within uas_zap_pending(), which is executed after usb_kill_anchored_urbs(). The error handling only takes effect when uas_queuecommand_lck() calls uas_submit_urbs() and returns the error value -ENODEV . In this case, the device is disconnected, and the flow proceeds to uas_disconnect(), where uas_zap_pending() is invoked to call uas_try_complete(). (CVE-2025-68331) In the Linux kernel, the following vulnerability has been resolved: libceph: replace BUG_ON with bounds check for map->max_osd OSD indexes come from untrusted network packets. Boundary checks are added to validate these against map->max_osd. [ idryomov: drop BUG_ON in ceph_get_primary_affinity(), minor cosmetic edits ] (CVE-2025-68283) In the Linux kernel, the following vulnerability has been resolved: ipv4: route: Prevent rt_bind_exception() from rebinding stale fnhe The sit driver_x27;s packet transmission path calls: sit_tunnel_xmit() -> update_or_create_fnhe(), which lead to fnhe_remove_oldest() being called to delete entries exceeding FNHE_RECLAIM_DEPTH+random. The race window is between fnhe_remove_oldest() selecting fnheX for deletion and the subsequent kfree_rcu(). During this time, the concurrent path_x27;s __mkroute_output() -> find_exception() can fetch the soon-to-be-deleted fnheX, and rt_bind_exception() then binds it with a new dst using a dst_hold(). When the original fnheX is freed via RCU, the dst reference remains permanently leaked. CPU 0 CPU 1 __mkroute_output() find_exception() [fnheX] update_or_create_fnhe() fnhe_remove_oldest() [fnheX] rt_bind_exception() [bind dst] RCU callback [fnheX freed, dst leak] This issue manifests as a device reference count leak and a warning in dmesg when unregistering the net device: unregister_netdevice: waiting for sitX to become free. Usage count = N Ido Schimmel provided the simple test validation method [1]. The fix clears _x27;oldest->fnhe_daddr_x27; before calling fnhe_flush_routes(). Since rt_bind_exception() checks this field, setting it to zero prevents the stale fnhe from being reused and bound to a new dst just before it is freed. [1] ip netns add ns1 ip -n ns1 link set dev lo up ip -n ns1 address add 192.0.2.1/32 dev lo ip -n ns1 link add name dummy1 up type dummy ip -n ns1 route add 192.0.2.2/32 dev dummy1 ip -n ns1 link add name gretap1 up arp off type gretap \ local 192.0.2.1 remote 192.0.2.2 ip -n ns1 route add 198.51.0.0/16 dev gretap1 taskset -c 0 ip netns exec ns1 mausezahn gretap1 \ -A 198.51.100.1 -B 198.51.0.0/16 -t udp -p 1000 -c 0 -q & taskset -c 2 ip netns exec ns1 mausezahn gretap1 \ -A 198.51.100.1 -B 198.51.0.0/16 -t udp -p 1000 -c 0 -q & sleep 10 ip netns pids ns1 | xargs kill ip netns del ns1 (CVE-2025-68241) In the Linux kernel, the following vulnerability has been resolved: ext4: guard against EA inode refcount underflow in xattr update syzkaller found a path where ext4_xattr_inode_update_ref() reads an EA inode refcount that is already <= 0 and then applies ref_change (often -1). That lets the refcount underflow and we proceed with a bogus value, triggering errors like: EXT4-fs error: EA inode <n> ref underflow: ref_count=-1 ref_change=-1 EXT4-fs warning: ea_inode dec ref err=-117 Make the invariant explicit: if the current refcount is non-positive, treat this as on-disk corruption, emit ext4_error_inode(), and fail the operation with -EFSCORRUPTED instead of updating the refcount. Delete the WARN_ONCE() as negative refcounts are now impossible; keep error reporting in ext4_error_inode(). This prevents the underflow and the follow-on orphan/cleanup churn. (CVE-2025-40190) In the Linux kernel, the following vulnerability has been resolved: net: rfkill: gpio: Fix crash due to dereferencering uninitialized pointer Since commit 7d5e9737efda ("net: rfkill: gpio: get the name and type from device property") rfkill_find_type() gets called with the possibly uninitialized "const char *type_name;" local variable. On x86 systems when rfkill-gpio binds to a "BCM4752" or "LNV4752" acpi_device, the rfkill->type is set based on the ACPI acpi_device_id: rfkill->type = (unsigned)id->driver_data; and there is no "type" property so device_property_read_string() will fail and leave type_name uninitialized, leading to a potential crash. rfkill_find_type() does accept a NULL pointer, fix the potential crash by initializing type_name to NULL. Note likely sofar this has not been caught because: 1. Not many x86 machines actually have a "BCM4752"/"LNV4752" acpi_device 2. The stack happened to contain NULL where type_name is stored (CVE-2025-39937) In the Linux kernel, the following vulnerability has been resolved: RDMA/bnxt_re: Prevent handling any completions after qp destroy HW may generate completions that indicates QP is destroyed. Driver should not be scheduling any more completion handlers for this QP, after the QP is destroyed. Since CQs are active during the QP destroy, driver may still schedule completion handlers. This can cause a race where the destroy_cq and poll_cq running simultaneously. Snippet of kernel panic while doing bnxt_re driver load unload in loop. This indicates a poll after the CQ is freed. [77786.481636] Call Trace: [77786.481640] <TASK> [77786.481644] bnxt_re_poll_cq+0x14a/0x620 [bnxt_re] [77786.481658] ? kvm_clock_read+0x14/0x30 [77786.481693] __ib_process_cq+0x57/0x190 [ib_core] [77786.481728] ib_cq_poll_work+0x26/0x80 [ib_core] [77786.481761] process_one_work+0x1e5/0x3f0 [77786.481768] worker_thread+0x50/0x3a0 [77786.481785] ? __pfx_worker_thread+0x10/0x10 [77786.481790] kthread+0xe2/0x110 [77786.481794] ? __pfx_kthread+0x10/0x10 [77786.481797] ret_from_fork+0x2c/0x50 To avoid this, complete all completion handlers before returning the destroy QP. If free_cq is called soon after destroy_qp, IB stack will cancel the CQ work before invoking the destroy_cq verb and this will prevent any race mentioned. (CVE-2023-54048) In the Linux kernel, the following vulnerability has been resolved: scsi: sg: Do not sleep in atomic context sg_finish_rem_req() calls blk_rq_unmap_user(). The latter function may sleep. Hence, call sg_finish_rem_req() with interrupts enabled instead of disabled. (CVE-2025-40259) In the Linux kernel, the following vulnerability has been resolved: vsock: Ignore signal/timeout on connect() if already established During connect(), acting on a signal/timeout by disconnecting an already established socket leads to several issues: 1. connect() invoking vsock_transport_cancel_pkt() -> virtio_transport_purge_skbs() may race with sendmsg() invoking virtio_transport_get_credit(). This results in a permanently elevated `vvs->bytes_unsent`. Which, in turn, confuses the SOCK_LINGER handling. 2. connect() resetting a connected socket_x27;s state may race with socket being placed in a sockmap. A disconnected socket remaining in a sockmap breaks sockmap_x27;s assumptions. And gives rise to WARNs. 3. connect() transitioning SS_CONNECTED -> SS_UNCONNECTED allows for a transport change/drop after TCP_ESTABLISHED. Which poses a problem for any simultaneous sendmsg() or connect() and may result in a use-after-free/null-ptr-deref. Do not disconnect socket on signal/timeout. Keep the logic for unconnected sockets: they don_x27;t linger, can_x27;t be placed in a sockmap, are rejected by sendmsg(). [1]: https://lore.kernel.org/netdev/e07fd95c-9a38-4eea-9638-133e38c2ec9b@rbox.co/ [2]: https://lore.kernel.org/netdev/20250317-vsock-trans-signal-race-v4-0-fc8837f3f1d4@rbox.co/ [3]: https://lore.kernel.org/netdev/60f1b7db-3099-4f6a-875e-af9f6ef194f6@rbox.co/ (CVE-2025-40248) In the Linux kernel, the following vulnerability has been resolved: bpf: Explicitly check accesses to bpf_sock_addr Syzkaller found a kernel warning on the following sock_addr program: 0: r0 = 0 1: r2 = *(u32 *)(r1 +60) 2: exit which triggers: verifier bug: error during ctx access conversion (0) This is happening because offset 60 in bpf_sock_addr corresponds to an implicit padding of 4 bytes, right after msg_src_ip4. Access to this padding isn_x27;t rejected in sock_addr_is_valid_access and it thus later fails to convert the access. This patch fixes it by explicitly checking the various fields of bpf_sock_addr in sock_addr_is_valid_access. I checked the other ctx structures and is_valid_access functions and didn_x27;t find any other similar cases. Other cases of (properly handled) padding are covered in new tests in a subsequent patch. (CVE-2025-40078) In the Linux kernel, the following vulnerability has been resolved: tcp: use dst_dev_rcu() in tcp_fastopen_active_disable_ofo_check() Use RCU to avoid a pair of atomic operations and a potential UAF on dst_dev()->flags. (CVE-2025-68188) In the Linux kernel, the following vulnerability has been resolved: x86/apic: Don_x27;t disable x2APIC if locked The APIC supports two modes, legacy APIC (or xAPIC), and Extended APIC (or x2APIC). X2APIC mode is mostly compatible with legacy APIC, but it disables the memory-mapped APIC interface in favor of one that uses MSRs. The APIC mode is controlled by the EXT bit in the APIC MSR. The MMIO/xAPIC interface has some problems, most notably the APIC LEAK [1]. This bug allows an attacker to use the APIC MMIO interface to extract data from the SGX enclave. Introduce support for a new feature that will allow the BIOS to lock the APIC in x2APIC mode. If the APIC is locked in x2APIC mode and the kernel tries to disable the APIC or revert to legacy APIC mode a GP fault will occur. Introduce support for a new MSR (IA32_XAPIC_DISABLE_STATUS) and handle the new locked mode when the LEGACY_XAPIC_DISABLED bit is set by preventing the kernel from trying to disable the x2APIC. On platforms with the IA32_XAPIC_DISABLE_STATUS MSR, if SGX or TDX are enabled the LEGACY_XAPIC_DISABLED will be set by the BIOS. If legacy APIC is required, then it SGX and TDX need to be disabled in the BIOS. [1]: https://aepicleak.com/aepicleak.pdf (CVE-2022-50720) In the Linux kernel, the following vulnerability has been resolved: futex: Don_x27;t leak robust_list pointer on exec race sys_get_robust_list() and compat_get_robust_list() use ptrace_may_access() to check if the calling task is allowed to access another task_x27;s robust_list pointer. This check is racy against a concurrent exec() in the target process. During exec(), a task may transition from a non-privileged binary to a privileged one (e.g., setuid binary) and its credentials/memory mappings may change. If get_robust_list() performs ptrace_may_access() before this transition, it may erroneously allow access to sensitive information after the target becomes privileged. A racy access allows an attacker to exploit a window during which ptrace_may_access() passes before a target process transitions to a privileged state via exec(). For example, consider a non-privileged task T that is about to execute a setuid-root binary. An attacker task A calls get_robust_list(T) while T is still unprivileged. Since ptrace_may_access() checks permissions based on current credentials, it succeeds. However, if T begins exec immediately afterwards, it becomes privileged and may change its memory mappings. Because get_robust_list() proceeds to access T->robust_list without synchronizing with exec() it may read user-space pointers from a now-privileged process. This violates the intended post-exec access restrictions and could expose sensitive memory addresses or be used as a primitive in a larger exploit chain. Consequently, the race can lead to unauthorized disclosure of information across privilege boundaries and poses a potential security risk. Take a read lock on signal->exec_update_lock prior to invoking ptrace_may_access() and accessing the robust_list/compat_robust_list. This ensures that the target task_x27;s exec state remains stable during the check, allowing for consistent and synchronized validation of credentials. (CVE-2025-40341) In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Fix null deref on srq->rq.queue after resize failure A NULL pointer dereference can occur in rxe_srq_chk_attr() when ibv_modify_srq() is invoked twice in succession under certain error conditions. The first call may fail in rxe_queue_resize(), which leads rxe_srq_from_attr() to set srq->rq.queue = NULL. The second call then triggers a crash (null deref) when accessing srq->rq.queue->buf->index_mask. Call Trace: <TASK> rxe_modify_srq+0x170/0x480 [rdma_rxe] ? __pfx_rxe_modify_srq+0x10/0x10 [rdma_rxe] ? uverbs_try_lock_object+0x4f/0xa0 [ib_uverbs] ? rdma_lookup_get_uobject+0x1f0/0x380 [ib_uverbs] ib_uverbs_modify_srq+0x204/0x290 [ib_uverbs] ? __pfx_ib_uverbs_modify_srq+0x10/0x10 [ib_uverbs] ? tryinc_node_nr_active+0xe6/0x150 ? uverbs_fill_udata+0xed/0x4f0 [ib_uverbs] ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0x2c0/0x470 [ib_uverbs] ? __pfx_ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0x10/0x10 [ib_uverbs] ? uverbs_fill_udata+0xed/0x4f0 [ib_uverbs] ib_uverbs_run_method+0x55a/0x6e0 [ib_uverbs] ? __pfx_ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0x10/0x10 [ib_uverbs] ib_uverbs_cmd_verbs+0x54d/0x800 [ib_uverbs] ? __pfx_ib_uverbs_cmd_verbs+0x10/0x10 [ib_uverbs] ? __pfx___raw_spin_lock_irqsave+0x10/0x10 ? __pfx_do_vfs_ioctl+0x10/0x10 ? ioctl_has_perm.constprop.0.isra.0+0x2c7/0x4c0 ? __pfx_ioctl_has_perm.constprop.0.isra.0+0x10/0x10 ib_uverbs_ioctl+0x13e/0x220 [ib_uverbs] ? __pfx_ib_uverbs_ioctl+0x10/0x10 [ib_uverbs] __x64_sys_ioctl+0x138/0x1c0 do_syscall_64+0x82/0x250 ? fdget_pos+0x58/0x4c0 ? ksys_write+0xf3/0x1c0 ? __pfx_ksys_write+0x10/0x10 ? do_syscall_64+0xc8/0x250 ? __pfx_vm_mmap_pgoff+0x10/0x10 ? fget+0x173/0x230 ? fput+0x2a/0x80 ? ksys_mmap_pgoff+0x224/0x4c0 ? do_syscall_64+0xc8/0x250 ? do_user_addr_fault+0x37b/0xfe0 ? clear_bhb_loop+0x50/0xa0 ? clear_bhb_loop+0x50/0xa0 ? clear_bhb_loop+0x50/0xa0 entry_SYSCALL_64_after_hwframe+0x76/0x7e (CVE-2025-68379) In the Linux kernel, the following vulnerability has been resolved: timers: Fix NULL function pointer race in timer_shutdown_sync() There is a race condition between timer_shutdown_sync() and timer expiration that can lead to hitting a WARN_ON in expire_timers(). The issue occurs when timer_shutdown_sync() clears the timer function to NULL while the timer is still running on another CPU. The race scenario looks like this: CPU0 CPU1 <SOFTIRQ> lock_timer_base() expire_timers() base->running_timer = timer; unlock_timer_base() [call_timer_fn enter] mod_timer() ... timer_shutdown_sync() lock_timer_base() // For now, will not detach the timer but only clear its function to NULL if (base->running_timer != timer) ret = detach_if_pending(timer, base, true); if (shutdown) timer->function = NULL; unlock_timer_base() [call_timer_fn exit] lock_timer_base() base->running_timer = NULL; unlock_timer_base() ... // Now timer is pending while its function set to NULL. // next timer trigger <SOFTIRQ> expire_timers() WARN_ON_ONCE(!fn) // hit ... lock_timer_base() // Now timer will detach if (base->running_timer != timer) ret = detach_if_pending(timer, base, true); if (shutdown) timer->function = NULL; unlock_timer_base() The problem is that timer_shutdown_sync() clears the timer function regardless of whether the timer is currently running. This can leave a pending timer with a NULL function pointer, which triggers the WARN_ON_ONCE(!fn) check in expire_timers(). Fix this by only clearing the timer function when actually detaching the timer. If the timer is running, leave the function pointer intact, which is safe because the timer will be properly detached when it finishes running. (CVE-2025-68214) In the Linux kernel, the following vulnerability has been resolved: ipv6/sit: use DEV_STATS_INC() to avoid data-races syzbot/KCSAN reported that multiple cpus are updating dev->stats.tx_error concurrently. This is because sit tunnels are NETIF_F_LLTX, meaning their ndo_start_xmit() is not protected by a spinlock. While original KCSAN report was about tx path, rx path has the same issue. (CVE-2022-50764) In the Linux kernel, the following vulnerability has been resolved: block: avoid possible overflow for chunk_sectors check in blk_stack_limits() In blk_stack_limits(), we check that the t->chunk_sectors value is a multiple of the t->physical_block_size value. However, by finding the chunk_sectors value in bytes, we may overflow the unsigned int which holds chunk_sectors, so change the check to be based on sectors. (CVE-2025-39795) In the Linux kernel, the following vulnerability has been resolved: crypto: hisilicon/qm - request reserved interrupt for virtual function The device interrupt vector 3 is an error interrupt for physical function and a reserved interrupt for virtual function. However, the driver has not registered the reserved interrupt for virtual function. When allocating interrupts, the number of interrupts is allocated based on powers of two, which includes this interrupt. When the system enables GICv4 and the virtual function passthrough to the virtual machine, releasing the interrupt in the driver triggers a warning. The WARNING report is: WARNING: CPU: 62 PID: 14889 at arch/arm64/kvm/vgic/vgic-its.c:852 its_free_ite+0x94/0xb4 Therefore, register a reserved interrupt for VF and set the IRQF_NO_AUTOEN flag to avoid that warning. (CVE-2025-40136) In the Linux kernel, the following vulnerability has been resolved: macintosh/mac_hid: fix race condition in mac_hid_toggle_emumouse The following warning appears when running syzkaller, and this issue also exists in the mainline code. ------------[ cut here ]------------ list_add double add: new=ffffffffa57eee28, prev=ffffffffa57eee28, next=ffffffffa5e63100. WARNING: CPU: 0 PID: 1491 at lib/list_debug.c:35 __list_add_valid_or_report+0xf7/0x130 Modules linked in: CPU: 0 PID: 1491 Comm: syz.1.28 Not tainted 6.6.0+ #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:__list_add_valid_or_report+0xf7/0x130 RSP: 0018:ff1100010dfb7b78 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffffffa57eee18 RCX: ffffffff97fc9817 RDX: 0000000000040000 RSI: ffa0000002383000 RDI: 0000000000000001 RBP: ffffffffa57eee28 R08: 0000000000000001 R09: ffe21c0021bf6f2c R10: 0000000000000001 R11: 6464615f7473696c R12: ffffffffa5e63100 R13: ffffffffa57eee28 R14: ffffffffa57eee28 R15: ff1100010dfb7d48 FS: 00007fb14398b640(0000) GS:ff11000119600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000010d096005 CR4: 0000000000773ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 80000000 Call Trace: <TASK> input_register_handler+0xb3/0x210 mac_hid_start_emulation+0x1c5/0x290 mac_hid_toggle_emumouse+0x20a/0x240 proc_sys_call_handler+0x4c2/0x6e0 new_sync_write+0x1b1/0x2d0 vfs_write+0x709/0x950 ksys_write+0x12a/0x250 do_syscall_64+0x5a/0x110 entry_SYSCALL_64_after_hwframe+0x78/0xe2 The WARNING occurs when two processes concurrently write to the mac-hid emulation sysctl, causing a race condition in mac_hid_toggle_emumouse(). Both processes read old_val=0, then both try to register the input handler, leading to a double list_add of the same handler. CPU0 CPU1 ------------------------- ------------------------- vfs_write() //write 1 vfs_write() //write 1 proc_sys_write() proc_sys_write() mac_hid_toggle_emumouse() mac_hid_toggle_emumouse() old_val = *valp // old_val=0 old_val = *valp // old_val=0 mutex_lock_killable() proc_dointvec() // *valp=1 mac_hid_start_emulation() input_register_handler() mutex_unlock() mutex_lock_killable() proc_dointvec() mac_hid_start_emulation() input_register_handler() //Trigger Warning mutex_unlock() Fix this by moving the old_val read inside the mutex lock region. (CVE-2025-68367) In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_mr: Fix use-after-free when updating multicast route stats Cited commit added a dedicated mutex (instead of RTNL) to protect the multicast route list, so that it will not change while the driver periodically traverses it in order to update the kernel about multicast route stats that were queried from the device. One instance of list entry deletion (during route replace) was missed and it can result in a use-after-free [1]. Fix by acquiring the mutex before deleting the entry from the list and releasing it afterwards. [1] BUG: KASAN: slab-use-after-free in mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum] Read of size 8 at addr ffff8881523c2fa8 by task kworker/2:5/22043 CPU: 2 UID: 0 PID: 22043 Comm: kworker/2:5 Not tainted 6.18.0-rc1-custom-g1a3d6d7cd014 #1 PREEMPT(full) Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017 Workqueue: mlxsw_core mlxsw_sp_mr_stats_update [mlxsw_spectrum] Call Trace: <TASK> dump_stack_lvl+0xba/0x110 print_report+0x174/0x4f5 kasan_report+0xdf/0x110 mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum] process_one_work+0x9cc/0x18e0 worker_thread+0x5df/0xe40 kthread+0x3b8/0x730 ret_from_fork+0x3e9/0x560 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 29933: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x8f/0xa0 mlxsw_sp_mr_route_add+0xd8/0x4770 [mlxsw_spectrum] mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum] process_one_work+0x9cc/0x18e0 worker_thread+0x5df/0xe40 kthread+0x3b8/0x730 ret_from_fork+0x3e9/0x560 ret_from_fork_asm+0x1a/0x30 Freed by task 29933: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_save_free_info+0x3b/0x70 __kasan_slab_free+0x43/0x70 kfree+0x14e/0x700 mlxsw_sp_mr_route_add+0x2dea/0x4770 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:444 [mlxsw_spectrum] mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum] process_one_work+0x9cc/0x18e0 worker_thread+0x5df/0xe40 kthread+0x3b8/0x730 ret_from_fork+0x3e9/0x560 ret_from_fork_asm+0x1a/0x30 (CVE-2025-68800) In the Linux kernel, the following vulnerability has been resolved: Squashfs: reject negative file sizes in squashfs_read_inode() Syskaller reports a "WARNING in ovl_copy_up_file" in overlayfs. This warning is ultimately caused because the underlying Squashfs file system returns a file with a negative file size. This commit checks for a negative file size and returns EINVAL. [phillip@squashfs.org.uk: only need to check 64 bit quantity] (CVE-2025-40200) In the Linux kernel, the following vulnerability has been resolved: usb: storage: Fix memory leak in USB bulk transport A kernel memory leak was identified by the _x27;ioctl_sg01_x27; test from Linux Test Project (LTP). The following bytes were mainly observed: 0x53425355. When USB storage devices incorrectly skip the data phase with status data, the code extracts/validates the CSW from the sg buffer, but fails to clear it afterwards. This leaves status protocol data in srb_x27;s transfer buffer, such as the US_BULK_CS_SIGN _x27;USBS_x27; signature observed here. Thus, this can lead to USB protocols leaks to user space through SCSI generic (/dev/sg*) interfaces, such as the one seen here when the LTP test requested 512 KiB. Fix the leak by zeroing the CSW data in srb_x27;s transfer buffer immediately after the validation of devices that skip data phase. Note: Differently from CVE-2018-1000204, which fixed a big leak by zero- ing pages at allocation time, this leak occurs after allocation, when USB protocol data is written to already-allocated sg pages. (CVE-2025-68288) In the Linux kernel, the following vulnerability has been resolved: of: check previous kernel_x27;s ima-kexec-buffer against memory bounds Presently ima_get_kexec_buffer() doesn_x27;t check if the previous kernel_x27;s ima-kexec-buffer lies outside the addressable memory range. This can result in a kernel panic if the new kernel is booted with _x27;mem=X_x27; arg and the ima-kexec-buffer was allocated beyond that range by the previous kernel. The panic is usually of the form below: $ sudo kexec --initrd initrd vmlinux --append=_x27;mem=16G_x27; <snip> BUG: Unable to handle kernel data access on read at 0xc000c01fff7f0000 Faulting instruction address: 0xc000000000837974 Oops: Kernel access of bad area, sig: 11 [#1] <snip> NIP [c000000000837974] ima_restore_measurement_list+0x94/0x6c0 LR [c00000000083b55c] ima_load_kexec_buffer+0xac/0x160 Call Trace: [c00000000371fa80] [c00000000083b55c] ima_load_kexec_buffer+0xac/0x160 [c00000000371fb00] [c0000000020512c4] ima_init+0x80/0x108 [c00000000371fb70] [c0000000020514dc] init_ima+0x4c/0x120 [c00000000371fbf0] [c000000000012240] do_one_initcall+0x60/0x2c0 [c00000000371fcc0] [c000000002004ad0] kernel_init_freeable+0x344/0x3ec [c00000000371fda0] [c0000000000128a4] kernel_init+0x34/0x1b0 [c00000000371fe10] [c00000000000ce64] ret_from_kernel_thread+0x5c/0x64 Instruction dump: f92100b8 f92100c0 90e10090 910100a0 4182050c 282a0017 3bc00000 40810330 7c0802a6 fb610198 7c9b2378 f80101d0 <a1240000> 2c090001 40820614 e9240010 ---[ end trace 0000000000000000 ]--- Fix this issue by checking returned PFN range of previous kernel_x27;s ima-kexec-buffer with page_is_ram() to ensure correct memory bounds. (CVE-2022-50159) In the Linux kernel, the following vulnerability has been resolved: netfilter: xt_nfacct: don_x27;t assume acct name is null-terminated BUG: KASAN: slab-out-of-bounds in .. lib/vsprintf.c:721 Read of size 1 at addr ffff88801eac95c8 by task syz-executor183/5851 [..] string+0x231/0x2b0 lib/vsprintf.c:721 vsnprintf+0x739/0xf00 lib/vsprintf.c:2874 [..] nfacct_mt_checkentry+0xd2/0xe0 net/netfilter/xt_nfacct.c:41 xt_check_match+0x3d1/0xab0 net/netfilter/x_tables.c:523 nfnl_acct_find_get() handles non-null input, but the error printk relied on its presence. (CVE-2025-38639) In the Linux kernel, the following vulnerability has been resolved: of: overlay: Call of_changeset_init() early When of_overlay_fdt_apply() fails, the changeset may be partially applied, and the caller is still expected to call of_overlay_remove() to clean up this partial state. However, of_overlay_apply() calls of_resolve_phandles() before init_overlay_changeset(). Hence if the overlay fails to apply due to an unresolved symbol, the overlay_changeset.cset.entries list is still uninitialized, and cleanup will crash with a NULL-pointer dereference in overlay_removal_is_ok(). Fix this by moving the call to of_changeset_init() from init_overlay_changeset() to of_overlay_fdt_apply(), where all other early initialization is done. (CVE-2023-53856) In the Linux kernel, the following vulnerability has been resolved: Squashfs: fix uninit-value in squashfs_get_parent Syzkaller reports a "KMSAN: uninit-value in squashfs_get_parent" bug. This is caused by open_by_handle_at() being called with a file handle containing an invalid parent inode number. In particular the inode number is that of a symbolic link, rather than a directory. Squashfs_get_parent() gets called with that symbolic link inode, and accesses the parent member field. unsigned int parent_ino = squashfs_i(inode)->parent; Because non-directory inodes in Squashfs do not have a parent value, this is uninitialised, and this causes an uninitialised value access. The fix is to initialise parent with the invalid inode 0, which will cause an EINVAL error to be returned. Regular inodes used to share the parent field with the block_list_start field. This is removed in this commit to enable the parent field to contain the invalid inode number 0. (CVE-2025-40049) In the Linux kernel, the following vulnerability has been resolved: ext4: refresh inline data size before write operations The cached ei->i_inline_size can become stale between the initial size check and when ext4_update_inline_data()/ext4_create_inline_data() use it. Although ext4_get_max_inline_size() reads the correct value at the time of the check, concurrent xattr operations can modify i_inline_size before ext4_write_lock_xattr() is acquired. This causes ext4_update_inline_data() and ext4_create_inline_data() to work with stale capacity values, leading to a BUG_ON() crash in ext4_write_inline_data(): kernel BUG at fs/ext4/inline.c:1331! BUG_ON(pos + len > EXT4_I(inode)->i_inline_size); The race window: 1. ext4_get_max_inline_size() reads i_inline_size = 60 (correct) 2. Size check passes for 50-byte write 3. [Another thread adds xattr, i_inline_size changes to 40] 4. ext4_write_lock_xattr() acquires lock 5. ext4_update_inline_data() uses stale i_inline_size = 60 6. Attempts to write 50 bytes but only 40 bytes actually available 7. BUG_ON() triggers Fix this by recalculating i_inline_size via ext4_find_inline_data_nolock() immediately after acquiring xattr_sem. This ensures ext4_update_inline_data() and ext4_create_inline_data() work with current values that are protected from concurrent modifications. This is similar to commit a54c4613dac1 ("ext4: fix race writing to an inline_data file while its xattrs are changing") which fixed i_inline_off staleness. This patch addresses the related i_inline_size staleness issue. (CVE-2025-68264) Rejected reason: This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. (CVE-2025-37942) In the Linux kernel, the following vulnerability has been resolved: KVM: Destroy target device if coalesced MMIO unregistration fails Destroy and free the target coalesced MMIO device if unregistering said device fails. As clearly noted in the code, kvm_io_bus_unregister_dev() does not destroy the target device. BUG: memory leak unreferenced object 0xffff888112a54880 (size 64): comm "syz-executor.2", pid 5258, jiffies 4297861402 (age 14.129s) hex dump (first 32 bytes): 38 c7 67 15 00 c9 ff ff 38 c7 67 15 00 c9 ff ff 8.g.....8.g..... e0 c7 e1 83 ff ff ff ff 00 30 67 15 00 c9 ff ff .........0g..... backtrace: [<0000000006995a8a>] kmalloc include/linux/slab.h:556 [inline] [<0000000006995a8a>] kzalloc include/linux/slab.h:690 [inline] [<0000000006995a8a>] kvm_vm_ioctl_register_coalesced_mmio+0x8e/0x3d0 arch/x86/kvm/../../../virt/kvm/coalesced_mmio.c:150 [<00000000022550c2>] kvm_vm_ioctl+0x47d/0x1600 arch/x86/kvm/../../../virt/kvm/kvm_main.c:3323 [<000000008a75102f>] vfs_ioctl fs/ioctl.c:46 [inline] [<000000008a75102f>] file_ioctl fs/ioctl.c:509 [inline] [<000000008a75102f>] do_vfs_ioctl+0xbab/0x1160 fs/ioctl.c:696 [<0000000080e3f669>] ksys_ioctl+0x76/0xa0 fs/ioctl.c:713 [<0000000059ef4888>] __do_sys_ioctl fs/ioctl.c:720 [inline] [<0000000059ef4888>] __se_sys_ioctl fs/ioctl.c:718 [inline] [<0000000059ef4888>] __x64_sys_ioctl+0x6f/0xb0 fs/ioctl.c:718 [<000000006444fa05>] do_syscall_64+0x9f/0x4e0 arch/x86/entry/common.c:290 [<000000009a4ed50b>] entry_SYSCALL_64_after_hwframe+0x49/0xbe BUG: leak checking failed (CVE-2023-54024) In the Linux kernel, the following vulnerability has been resolved: ext4: add i_data_sem protection in ext4_destroy_inline_data_nolock() Fix a race between inline data destruction and block mapping. The function ext4_destroy_inline_data_nolock() changes the inode data layout by clearing EXT4_INODE_INLINE_DATA and setting EXT4_INODE_EXTENTS. At the same time, another thread may execute ext4_map_blocks(), which tests EXT4_INODE_EXTENTS to decide whether to call ext4_ext_map_blocks() or ext4_ind_map_blocks(). Without i_data_sem protection, ext4_ind_map_blocks() may receive inode with EXT4_INODE_EXTENTS flag and triggering assert. kernel BUG at fs/ext4/indirect.c:546! EXT4-fs (loop2): unmounting filesystem. invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014 RIP: 0010:ext4_ind_map_blocks.cold+0x2b/0x5a fs/ext4/indirect.c:546 Call Trace: <TASK> ext4_map_blocks+0xb9b/0x16f0 fs/ext4/inode.c:681 _ext4_get_block+0x242/0x590 fs/ext4/inode.c:822 ext4_block_write_begin+0x48b/0x12c0 fs/ext4/inode.c:1124 ext4_write_begin+0x598/0xef0 fs/ext4/inode.c:1255 ext4_da_write_begin+0x21e/0x9c0 fs/ext4/inode.c:3000 generic_perform_write+0x259/0x5d0 mm/filemap.c:3846 ext4_buffered_write_iter+0x15b/0x470 fs/ext4/file.c:285 ext4_file_write_iter+0x8e0/0x17f0 fs/ext4/file.c:679 call_write_iter include/linux/fs.h:2271 [inline] do_iter_readv_writev+0x212/0x3c0 fs/read_write.c:735 do_iter_write+0x186/0x710 fs/read_write.c:861 vfs_iter_write+0x70/0xa0 fs/read_write.c:902 iter_file_splice_write+0x73b/0xc90 fs/splice.c:685 do_splice_from fs/splice.c:763 [inline] direct_splice_actor+0x10f/0x170 fs/splice.c:950 splice_direct_to_actor+0x33a/0xa10 fs/splice.c:896 do_splice_direct+0x1a9/0x280 fs/splice.c:1002 do_sendfile+0xb13/0x12c0 fs/read_write.c:1255 __do_sys_sendfile64 fs/read_write.c:1323 [inline] __se_sys_sendfile64 fs/read_write.c:1309 [inline] __x64_sys_sendfile64+0x1cf/0x210 fs/read_write.c:1309 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x35/0x80 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 (CVE-2025-68261) In the Linux kernel, the following vulnerability has been resolved: sctp: Prevent TOCTOU out-of-bounds write For the following path not holding the sock lock, sctp_diag_dump() -> sctp_for_each_endpoint() -> sctp_ep_dump() make sure not to exceed bounds in case the address list has grown between buffer allocation (time-of-check) and write (time-of-use). (CVE-2025-40331) In the Linux kernel, the following vulnerability has been resolved: blk-mq: check kobject state_in_sysfs before deleting in blk_mq_unregister_hctx In __blk_mq_update_nr_hw_queues() the return value of blk_mq_sysfs_register_hctxs() is not checked. If sysfs creation for hctx fails, later changing the number of hw_queues or removing disk will trigger the following warning: kernfs: can not remove _x27;nr_tags_x27;, no directory WARNING: CPU: 2 PID: 637 at fs/kernfs/dir.c:1707 kernfs_remove_by_name_ns+0x13f/0x160 Call Trace: remove_files.isra.1+0x38/0xb0 sysfs_remove_group+0x4d/0x100 sysfs_remove_groups+0x31/0x60 __kobject_del+0x23/0xf0 kobject_del+0x17/0x40 blk_mq_unregister_hctx+0x5d/0x80 blk_mq_sysfs_unregister_hctxs+0x94/0xd0 blk_mq_update_nr_hw_queues+0x124/0x760 nullb_update_nr_hw_queues+0x71/0xf0 [null_blk] nullb_device_submit_queues_store+0x92/0x120 [null_blk] kobjct_del() was called unconditionally even if sysfs creation failed. Fix it by checkig the kobject creation statusbefore deleting it. (CVE-2025-40125) In the Linux kernel, the following vulnerability has been resolved: netfilter: ctnetlink: remove refcounting in expectation dumpers Same pattern as previous patch: do not keep the expectation object alive via refcount, only store a cookie value and then use that as the skip hint for dump resumption. AFAICS this has the same issue as the one resolved in the conntrack dumper, when we do if (!refcount_inc_not_zero(&exp->use)) to increment the refcount, there is a chance that exp == last, which causes a double-increment of the refcount and subsequent memory leak. (CVE-2025-39764) In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Move representor neigh cleanup to profile cleanup_tx For IP tunnel encapsulation in ECMP (Equal-Cost Multipath) mode, as the flow is duplicated to the peer eswitch, the related neighbour information on the peer uplink representor is created as well. In the cited commit, eswitch devcom unpair is moved to uplink unload API, specifically the profile->cleanup_tx. If there is a encap rule offloaded in ECMP mode, when one eswitch does unpair (because of unloading the driver, for instance), and the peer rule from the peer eswitch is going to be deleted, the use-after-free error is triggered while accessing neigh info, as it is already cleaned up in uplink_x27;s profile->disable, which is before its profile->cleanup_tx. To fix this issue, move the neigh cleanup to profile_x27;s cleanup_tx callback, and after mlx5e_cleanup_uplink_rep_tx is called. The neigh init is moved to init_tx for symmeter. [ 2453.376299] BUG: KASAN: slab-use-after-free in mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core] [ 2453.379125] Read of size 4 at addr ffff888127af9008 by task modprobe/2496 [ 2453.381542] CPU: 7 PID: 2496 Comm: modprobe Tainted: G B 6.4.0-rc7+ #15 [ 2453.383386] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 2453.384335] Call Trace: [ 2453.384625] <TASK> [ 2453.384891] dump_stack_lvl+0x33/0x50 [ 2453.385285] print_report+0xc2/0x610 [ 2453.385667] ? __virt_addr_valid+0xb1/0x130 [ 2453.386091] ? mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core] [ 2453.386757] kasan_report+0xae/0xe0 [ 2453.387123] ? mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core] [ 2453.387798] mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core] [ 2453.388465] mlx5e_rep_encap_entry_detach+0xa6/0xe0 [mlx5_core] [ 2453.389111] mlx5e_encap_dealloc+0xa7/0x100 [mlx5_core] [ 2453.389706] mlx5e_tc_tun_encap_dests_unset+0x61/0xb0 [mlx5_core] [ 2453.390361] mlx5_free_flow_attr_actions+0x11e/0x340 [mlx5_core] [ 2453.391015] ? complete_all+0x43/0xd0 [ 2453.391398] ? free_flow_post_acts+0x38/0x120 [mlx5_core] [ 2453.392004] mlx5e_tc_del_fdb_flow+0x4ae/0x690 [mlx5_core] [ 2453.392618] mlx5e_tc_del_fdb_peers_flow+0x308/0x370 [mlx5_core] [ 2453.393276] mlx5e_tc_clean_fdb_peer_flows+0xf5/0x140 [mlx5_core] [ 2453.393925] mlx5_esw_offloads_unpair+0x86/0x540 [mlx5_core] [ 2453.394546] ? mlx5_esw_offloads_set_ns_peer.isra.0+0x180/0x180 [mlx5_core] [ 2453.395268] ? down_write+0xaa/0x100 [ 2453.395652] mlx5_esw_offloads_devcom_event+0x203/0x530 [mlx5_core] [ 2453.396317] mlx5_devcom_send_event+0xbb/0x190 [mlx5_core] [ 2453.396917] mlx5_esw_offloads_devcom_cleanup+0xb0/0xd0 [mlx5_core] [ 2453.397582] mlx5e_tc_esw_cleanup+0x42/0x120 [mlx5_core] [ 2453.398182] mlx5e_rep_tc_cleanup+0x15/0x30 [mlx5_core] [ 2453.398768] mlx5e_cleanup_rep_tx+0x6c/0x80 [mlx5_core] [ 2453.399367] mlx5e_detach_netdev+0xee/0x120 [mlx5_core] [ 2453.399957] mlx5e_netdev_change_profile+0x84/0x170 [mlx5_core] [ 2453.400598] mlx5e_vport_rep_unload+0xe0/0xf0 [mlx5_core] [ 2453.403781] mlx5_eswitch_unregister_vport_reps+0x15e/0x190 [mlx5_core] [ 2453.404479] ? mlx5_eswitch_register_vport_reps+0x200/0x200 [mlx5_core] [ 2453.405170] ? up_write+0x39/0x60 [ 2453.405529] ? kernfs_remove_by_name_ns+0xb7/0xe0 [ 2453.405985] auxiliary_bus_remove+0x2e/0x40 [ 2453.406405] device_release_driver_internal+0x243/0x2d0 [ 2453.406900] ? kobject_put+0x42/0x2d0 [ 2453.407284] bus_remove_device+0x128/0x1d0 [ 2453.407687] device_del+0x240/0x550 [ 2453.408053] ? waiting_for_supplier_show+0xe0/0xe0 [ 2453.408511] ? kobject_put+0xfa/0x2d0 [ 2453.408889] ? __kmem_cache_free+0x14d/0x280 [ 2453.409310] mlx5_rescan_drivers_locked.part.0+0xcd/0x2b0 [mlx5_core] [ 2453.409973] mlx5_unregister_device+0x40/0x50 [mlx5_core] [ 2453.410561] mlx5_uninit_one+0x3d/0x110 [mlx5_core] [ 2453.411111] remove_one+0x89/0x130 [mlx5_core] [ 24 ---truncated--- (CVE-2023-54148) In the Linux kernel, the following vulnerability has been resolved: crypto: hisilicon/qm - set NULL to qm->debug.qm_diff_regs When the initialization of qm->debug.acc_diff_reg fails, the probe process does not exit. However, after qm->debug.qm_diff_regs is freed, it is not set to NULL. This can lead to a double free when the remove process attempts to free it again. Therefore, qm->debug.qm_diff_regs should be set to NULL after it is freed. (CVE-2025-40062) In the Linux kernel, the following vulnerability has been resolved: Drivers: hv: vmbus: Don_x27;t dereference ACPI root object handle Since the commit referenced in the Fixes: tag below the VMBus client driver is walking the ACPI namespace up from the VMBus ACPI device to the ACPI namespace root object trying to find Hyper-V MMIO ranges. However, if it is not able to find them it ends trying to walk resources of the ACPI namespace root object itself. This object has all-ones handle, which causes a NULL pointer dereference in the ACPI code (from dereferencing this pointer with an offset). This in turn causes an oops on boot with VMBus host implementations that do not provide Hyper-V MMIO ranges in their VMBus ACPI device or its ancestors. The QEMU VMBus implementation is an example of such implementation. I guess providing these ranges is optional, since all tested Windows versions seem to be able to use VMBus devices without them. Fix this by explicitly terminating the lookup at the ACPI namespace root object. Note that Linux guests under KVM/QEMU do not use the Hyper-V PV interface by default - they only do so if the KVM PV interface is missing or disabled. Example stack trace of such oops: [ 3.710827] ? __die+0x1f/0x60 [ 3.715030] ? page_fault_oops+0x159/0x460 [ 3.716008] ? exc_page_fault+0x73/0x170 [ 3.716959] ? asm_exc_page_fault+0x22/0x30 [ 3.717957] ? acpi_ns_lookup+0x7a/0x4b0 [ 3.718898] ? acpi_ns_internalize_name+0x79/0xc0 [ 3.720018] acpi_ns_get_node_unlocked+0xb5/0xe0 [ 3.721120] ? acpi_ns_check_object_type+0xfe/0x200 [ 3.722285] ? acpi_rs_convert_aml_to_resource+0x37/0x6e0 [ 3.723559] ? down_timeout+0x3a/0x60 [ 3.724455] ? acpi_ns_get_node+0x3a/0x60 [ 3.725412] acpi_ns_get_node+0x3a/0x60 [ 3.726335] acpi_ns_evaluate+0x1c3/0x2c0 [ 3.727295] acpi_ut_evaluate_object+0x64/0x1b0 [ 3.728400] acpi_rs_get_method_data+0x2b/0x70 [ 3.729476] ? vmbus_platform_driver_probe+0x1d0/0x1d0 [hv_vmbus] [ 3.730940] ? vmbus_platform_driver_probe+0x1d0/0x1d0 [hv_vmbus] [ 3.732411] acpi_walk_resources+0x78/0xd0 [ 3.733398] vmbus_platform_driver_probe+0x9f/0x1d0 [hv_vmbus] [ 3.734802] platform_probe+0x3d/0x90 [ 3.735684] really_probe+0x19b/0x400 [ 3.736570] ? __device_attach_driver+0x100/0x100 [ 3.737697] __driver_probe_device+0x78/0x160 [ 3.738746] driver_probe_device+0x1f/0x90 [ 3.739743] __driver_attach+0xc2/0x1b0 [ 3.740671] bus_for_each_dev+0x70/0xc0 [ 3.741601] bus_add_driver+0x10e/0x210 [ 3.742527] driver_register+0x55/0xf0 [ 3.744412] ? 0xffffffffc039a000 [ 3.745207] hv_acpi_init+0x3c/0x1000 [hv_vmbus] (CVE-2023-53647) In the Linux kernel, the following vulnerability has been resolved: page_pool: always add GFP_NOWARN for ATOMIC allocations Driver authors often forget to add GFP_NOWARN for page allocation from the datapath. This is annoying to users as OOMs are a fact of life, and we pretty much expect network Rx to hit page allocation failures during OOM. Make page pool add GFP_NOWARN for ATOMIC allocations by default. (CVE-2025-68321) In the Linux kernel, the following vulnerability has been resolved: erofs: validate the extent length for uncompressed pclusters syzkaller reported a KASAN use-after-free: https://syzkaller.appspot.com/bug?extid=2ae90e873e97f1faf6f2 The referenced fuzzed image actually has two issues: - m_pa == 0 as a non-inlined pcluster; - The logical length is longer than its physical length. The first issue has already been addressed. This patch addresses the second issue by checking the extent length validity. (CVE-2022-50746) In the Linux kernel, the following vulnerability has been resolved: net: ipv6: fix field-spanning memcpy warning in AH output Fix field-spanning memcpy warnings in ah6_output() and ah6_output_done() where extension headers are copied to/from IPv6 address fields, triggering fortify-string warnings about writes beyond the 16-byte address fields. memcpy: detected field-spanning write (size 40) of single field "&top_iph->saddr" at net/ipv6/ah6.c:439 (size 16) WARNING: CPU: 0 PID: 8838 at net/ipv6/ah6.c:439 ah6_output+0xe7e/0x14e0 net/ipv6/ah6.c:439 The warnings are false positives as the extension headers are intentionally placed after the IPv6 header in memory. Fix by properly copying addresses and extension headers separately, and introduce helper functions to avoid code duplication. (CVE-2025-40363) In the Linux kernel, the following vulnerability has been resolved: nvmet-fc: avoid scheduling association deletion twice When forcefully shutting down a port via the configfs interface, nvmet_port_subsys_drop_link() first calls nvmet_port_del_ctrls() and then nvmet_disable_port(). Both functions will eventually schedule all remaining associations for deletion. The current implementation checks whether an association is about to be removed, but only after the work item has already been scheduled. As a result, it is possible for the first scheduled work item to free all resources, and then for the same work item to be scheduled again for deletion. Because the association list is an RCU list, it is not possible to take a lock and remove the list entry directly, so it cannot be looked up again. Instead, a flag (terminating) must be used to determine whether the association is already in the process of being deleted. (CVE-2025-40343) In the Linux kernel, the following vulnerability has been resolved: ksm: use range-walk function to jump over holes in scan_get_next_rmap_item Currently, scan_get_next_rmap_item() walks every page address in a VMA to locate mergeable pages. This becomes highly inefficient when scanning large virtual memory areas that contain mostly unmapped regions, causing ksmd to use large amount of cpu without deduplicating much pages. This patch replaces the per-address lookup with a range walk using walk_page_range(). The range walker allows KSM to skip over entire unmapped holes in a VMA, avoiding unnecessary lookups. This problem was previously discussed in [1]. Consider the following test program which creates a 32 TiB mapping in the virtual address space but only populates a single page: #include <unistd.h> #include <stdio.h> #include <sys/mman.h> /* 32 TiB */ const size_t size = 32ul * 1024 * 1024 * 1024 * 1024; int main() { char *area = mmap(NULL, size, PROT_READ | PROT_WRITE, MAP_NORESERVE | MAP_PRIVATE | MAP_ANON, -1, 0); if (area == MAP_FAILED) { perror("mmap() failed\n"); return -1; } /* Populate a single page such that we get an anon_vma. */ *area = 0; /* Enable KSM. */ madvise(area, size, MADV_MERGEABLE); pause(); return 0; } $ ./ksm-sparse & $ echo 1 > /sys/kernel/mm/ksm/run Without this patch ksmd uses 100% of the cpu for a long time (more then 1 hour in my test machine) scanning all the 32 TiB virtual address space that contain only one mapped page. This makes ksmd essentially deadlocked not able to deduplicate anything of value. With this patch ksmd walks only the one mapped page and skips the rest of the 32 TiB virtual address space, making the scan fast using little cpu. (CVE-2025-68211) In the Linux kernel, the following vulnerability has been resolved: usbnet: Prevents free active kevent The root cause of this issue are: 1. When probing the usbnet device, executing usbnet_link_change(dev, 0, 0); put the kevent work in global workqueue. However, the kevent has not yet been scheduled when the usbnet device is unregistered. Therefore, executing free_netdev() results in the "free active object (kevent)" error reported here. 2. Another factor is that when calling usbnet_disconnect()->unregister_netdev(), if the usbnet device is up, ndo_stop() is executed to cancel the kevent. However, because the device is not up, ndo_stop() is not executed. The solution to this problem is to cancel the kevent before executing free_netdev(). (CVE-2025-68312) In the Linux kernel, the following vulnerability has been resolved: net: atlantic: fix fragment overflow handling in RX path The atlantic driver can receive packets with more than MAX_SKB_FRAGS (17) fragments when handling large multi-descriptor packets. This causes an out-of-bounds write in skb_add_rx_frag_netmem() leading to kernel panic. The issue occurs because the driver doesn_x27;t check the total number of fragments before calling skb_add_rx_frag(). When a packet requires more than MAX_SKB_FRAGS fragments, the fragment index exceeds the array bounds. Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE, then all fragments are accounted for. And reusing the existing check to prevent the overflow earlier in the code path. This crash occurred in production with an Aquantia AQC113 10G NIC. Stack trace from production environment: ``` RIP: 0010:skb_add_rx_frag_netmem+0x29/0xd0 Code: 90 f3 0f 1e fa 0f 1f 44 00 00 48 89 f8 41 89 ca 48 89 d7 48 63 ce 8b 90 c0 00 00 00 48 c1 e1 04 48 01 ca 48 03 90 c8 00 00 00 <48> 89 7a 30 44 89 52 3c 44 89 42 38 40 f6 c7 01 75 74 48 89 fa 83 RSP: 0018:ffffa9bec02a8d50 EFLAGS: 00010287 RAX: ffff925b22e80a00 RBX: ffff925ad38d2700 RCX: fffffffe0a0c8000 RDX: ffff9258ea95bac0 RSI: ffff925ae0a0c800 RDI: 0000000000037a40 RBP: 0000000000000024 R08: 0000000000000000 R09: 0000000000000021 R10: 0000000000000848 R11: 0000000000000000 R12: ffffa9bec02a8e24 R13: ffff925ad8615570 R14: 0000000000000000 R15: ffff925b22e80a00 FS: 0000000000000000(0000) GS:ffff925e47880000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffff9258ea95baf0 CR3: 0000000166022004 CR4: 0000000000f72ef0 PKRU: 55555554 Call Trace: <IRQ> aq_ring_rx_clean+0x175/0xe60 [atlantic] ? aq_ring_rx_clean+0x14d/0xe60 [atlantic] ? aq_ring_tx_clean+0xdf/0x190 [atlantic] ? kmem_cache_free+0x348/0x450 ? aq_vec_poll+0x81/0x1d0 [atlantic] ? __napi_poll+0x28/0x1c0 ? net_rx_action+0x337/0x420 ``` Changes in v4: - Add Fixes: tag to satisfy patch validation requirements. Changes in v3: - Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE, then all fragments are accounted for. (CVE-2025-68301) In the Linux kernel, the following vulnerability has been resolved: bpf: Sync pending IRQ work before freeing ring buffer Fix a race where irq_work can be queued in bpf_ringbuf_commit() but the ring buffer is freed before the work executes. In the syzbot reproducer, a BPF program attached to sched_switch triggers bpf_ringbuf_commit(), queuing an irq_work. If the ring buffer is freed before this work executes, the irq_work thread may accesses freed memory. Calling `irq_work_sync(&rb->work)` ensures that all pending irq_work complete before freeing the buffer. (CVE-2025-40319) In the Linux kernel, the following vulnerability has been resolved: net: netpoll: fix incorrect refcount handling causing incorrect cleanup commit efa95b01da18 ("netpoll: fix use after free") incorrectly ignored the refcount and prematurely set dev->npinfo to NULL during netpoll cleanup, leading to improper behavior and memory leaks. Scenario causing lack of proper cleanup: 1) A netpoll is associated with a NIC (e.g., eth0) and netdev->npinfo is allocated, and refcnt = 1 - Keep in mind that npinfo is shared among all netpoll instances. In this case, there is just one. 2) Another netpoll is also associated with the same NIC and npinfo->refcnt += 1. - Now dev->npinfo->refcnt = 2; - There is just one npinfo associated to the netdev. 3) When the first netpolls goes to clean up: - The first cleanup succeeds and clears np->dev->npinfo, ignoring refcnt. - It basically calls `RCU_INIT_POINTER(np->dev->npinfo, NULL);` - Set dev->npinfo = NULL, without proper cleanup - No ->ndo_netpoll_cleanup() is either called 4) Now the second target tries to clean up - The second cleanup fails because np->dev->npinfo is already NULL. * In this case, ops->ndo_netpoll_cleanup() was never called, and the skb pool is not cleaned as well (for the second netpoll instance) - This leaks npinfo and skbpool skbs, which is clearly reported by kmemleak. Revert commit efa95b01da18 ("netpoll: fix use after free") and adds clarifying comments emphasizing that npinfo cleanup should only happen once the refcount reaches zero, ensuring stable and correct netpoll behavior. (CVE-2025-68245) In the Linux kernel, the following vulnerability has been resolved: fs/proc: fix uaf in proc_readdir_de() Pde is erased from subdir rbtree through rb_erase(), but not set the node to EMPTY, which may result in uaf access. We should use RB_CLEAR_NODE() set the erased node to EMPTY, then pde_subdir_next() will return NULL to avoid uaf access. We found an uaf issue while using stress-ng testing, need to run testcase getdent and tun in the same time. The steps of the issue is as follows: 1) use getdent to traverse dir /proc/pid/net/dev_snmp6/, and current pde is tun3; 2) in the [time windows] unregister netdevice tun3 and tun2, and erase them from rbtree. erase tun3 first, and then erase tun2. the pde(tun2) will be released to slab; 3) continue to getdent process, then pde_subdir_next() will return pde(tun2) which is released, it will case uaf access. CPU 0 | CPU 1 ------------------------------------------------------------------------- traverse dir /proc/pid/net/dev_snmp6/ | unregister_netdevice(tun->dev) //tun3 tun2 sys_getdents64() | iterate_dir() | proc_readdir() | proc_readdir_de() | snmp6_unregister_dev() pde_get(de); | proc_remove() read_unlock(&proc_subdir_lock); | remove_proc_subtree() | write_lock(&proc_subdir_lock); [time window] | rb_erase(&root->subdir_node, &parent->subdir); | write_unlock(&proc_subdir_lock); read_lock(&proc_subdir_lock); | next = pde_subdir_next(de); | pde_put(de); | de = next; //UAF | rbtree of dev_snmp6 | pde(tun3) / \ NULL pde(tun2) (CVE-2025-40271) In the Linux kernel, the following vulnerability has been resolved: md/raid0, raid10: Don_x27;t set discard sectors for request queue It should use disk_stack_limits to get a proper max_discard_sectors rather than setting a value by stack drivers. And there is a bug. If all member disks are rotational devices, raid0/raid10 set max_discard_sectors. So the member devices are not ssd/nvme, but raid0/raid10 export the wrong value. It reports warning messages in function __blkdev_issue_discard when mkfs.xfs like this: [ 4616.022599] ------------[ cut here ]------------ [ 4616.027779] WARNING: CPU: 4 PID: 99634 at block/blk-lib.c:50 __blkdev_issue_discard+0x16a/0x1a0 [ 4616.140663] RIP: 0010:__blkdev_issue_discard+0x16a/0x1a0 [ 4616.146601] Code: 24 4c 89 20 31 c0 e9 fe fe ff ff c1 e8 09 8d 48 ff 4c 89 f0 4c 09 e8 48 85 c1 0f 84 55 ff ff ff b8 ea ff ff ff e9 df fe ff ff <0f> 0b 48 8d 74 24 08 e8 ea d6 00 00 48 c7 c6 20 1e 89 ab 48 c7 c7 [ 4616.167567] RSP: 0018:ffffaab88cbffca8 EFLAGS: 00010246 [ 4616.173406] RAX: ffff9ba1f9e44678 RBX: 0000000000000000 RCX: ffff9ba1c9792080 [ 4616.181376] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9ba1c9792080 [ 4616.189345] RBP: 0000000000000cc0 R08: ffffaab88cbffd10 R09: 0000000000000000 [ 4616.197317] R10: 0000000000000012 R11: 0000000000000000 R12: 0000000000000000 [ 4616.205288] R13: 0000000000400000 R14: 0000000000000cc0 R15: ffff9ba1c9792080 [ 4616.213259] FS: 00007f9a5534e980(0000) GS:ffff9ba1b7c80000(0000) knlGS:0000000000000000 [ 4616.222298] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 4616.228719] CR2: 000055a390a4c518 CR3: 0000000123e40006 CR4: 00000000001706e0 [ 4616.236689] Call Trace: [ 4616.239428] blkdev_issue_discard+0x52/0xb0 [ 4616.244108] blkdev_common_ioctl+0x43c/0xa00 [ 4616.248883] blkdev_ioctl+0x116/0x280 [ 4616.252977] __x64_sys_ioctl+0x8a/0xc0 [ 4616.257163] do_syscall_64+0x5c/0x90 [ 4616.261164] ? handle_mm_fault+0xc5/0x2a0 [ 4616.265652] ? do_user_addr_fault+0x1d8/0x690 [ 4616.270527] ? do_syscall_64+0x69/0x90 [ 4616.274717] ? exc_page_fault+0x62/0x150 [ 4616.279097] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 4616.284748] RIP: 0033:0x7f9a55398c6b (CVE-2022-50583) In the Linux kernel, the following vulnerability has been resolved: nvme: nvme-fc: Ensure ->ioerr_work is cancelled in nvme_fc_delete_ctrl() nvme_fc_delete_assocation() waits for pending I/O to complete before returning, and an error can cause ->ioerr_work to be queued after cancel_work_sync() had been called. Move the call to cancel_work_sync() to be after nvme_fc_delete_association() to ensure ->ioerr_work is not running when the nvme_fc_ctrl object is freed. Otherwise the following can occur: [ 1135.911754] list_del corruption, ff2d24c8093f31f8->next is NULL [ 1135.917705] ------------[ cut here ]------------ [ 1135.922336] kernel BUG at lib/list_debug.c:52! [ 1135.926784] Oops: invalid opcode: 0000 [#1] SMP NOPTI [ 1135.931851] CPU: 48 UID: 0 PID: 726 Comm: kworker/u449:23 Kdump: loaded Not tainted 6.12.0 #1 PREEMPT(voluntary) [ 1135.943490] Hardware name: Dell Inc. PowerEdge R660/0HGTK9, BIOS 2.5.4 01/16/2025 [ 1135.950969] Workqueue: 0x0 (nvme-wq) [ 1135.954673] RIP: 0010:__list_del_entry_valid_or_report.cold+0xf/0x6f [ 1135.961041] Code: c7 c7 98 68 72 94 e8 26 45 fe ff 0f 0b 48 c7 c7 70 68 72 94 e8 18 45 fe ff 0f 0b 48 89 fe 48 c7 c7 80 69 72 94 e8 07 45 fe ff <0f> 0b 48 89 d1 48 c7 c7 a0 6a 72 94 48 89 c2 e8 f3 44 fe ff 0f 0b [ 1135.979788] RSP: 0018:ff579b19482d3e50 EFLAGS: 00010046 [ 1135.985015] RAX: 0000000000000033 RBX: ff2d24c8093f31f0 RCX: 0000000000000000 [ 1135.992148] RDX: 0000000000000000 RSI: ff2d24d6bfa1d0c0 RDI: ff2d24d6bfa1d0c0 [ 1135.999278] RBP: ff2d24c8093f31f8 R08: 0000000000000000 R09: ffffffff951e2b08 [ 1136.006413] R10: ffffffff95122ac8 R11: 0000000000000003 R12: ff2d24c78697c100 [ 1136.013546] R13: fffffffffffffff8 R14: 0000000000000000 R15: ff2d24c78697c0c0 [ 1136.020677] FS: 0000000000000000(0000) GS:ff2d24d6bfa00000(0000) knlGS:0000000000000000 [ 1136.028765] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1136.034510] CR2: 00007fd207f90b80 CR3: 000000163ea22003 CR4: 0000000000f73ef0 [ 1136.041641] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1136.048776] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 [ 1136.055910] PKRU: 55555554 [ 1136.058623] Call Trace: [ 1136.061074] <TASK> [ 1136.063179] ? show_trace_log_lvl+0x1b0/0x2f0 [ 1136.067540] ? show_trace_log_lvl+0x1b0/0x2f0 [ 1136.071898] ? move_linked_works+0x4a/0xa0 [ 1136.075998] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.081744] ? __die_body.cold+0x8/0x12 [ 1136.085584] ? die+0x2e/0x50 [ 1136.088469] ? do_trap+0xca/0x110 [ 1136.091789] ? do_error_trap+0x65/0x80 [ 1136.095543] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.101289] ? exc_invalid_op+0x50/0x70 [ 1136.105127] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.110874] ? asm_exc_invalid_op+0x1a/0x20 [ 1136.115059] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.120806] move_linked_works+0x4a/0xa0 [ 1136.124733] worker_thread+0x216/0x3a0 [ 1136.128485] ? __pfx_worker_thread+0x10/0x10 [ 1136.132758] kthread+0xfa/0x240 [ 1136.135904] ? __pfx_kthread+0x10/0x10 [ 1136.139657] ret_from_fork+0x31/0x50 [ 1136.143236] ? __pfx_kthread+0x10/0x10 [ 1136.146988] ret_from_fork_asm+0x1a/0x30 [ 1136.150915] </TASK> (CVE-2025-40261) In the Linux kernel, the following vulnerability has been resolved: NFSD: Fix crash in nfsd4_read_release() When tracing is enabled, the trace_nfsd_read_done trace point crashes during the pynfs read.testNoFh test. (CVE-2025-40324) In the Linux kernel, the following vulnerability has been resolved: net/sctp: fix a null dereference in sctp_disposition sctp_sf_do_5_1D_ce() If new_asoc->peer.adaptation_ind=0 and sctp_ulpevent_make_authkey=0 and sctp_ulpevent_make_authkey() returns 0, then the variable ai_ev remains zero and the zero will be dereferenced in the sctp_ulpevent_free() function. (CVE-2025-40187) In the Linux kernel, the following vulnerability has been resolved: netfilter: ctnetlink: fix refcount leak on table dump There is a reference count leak in ctnetlink_dump_table(): if (res < 0) { nf_conntrack_get(&ct->ct_general); // HERE cb->args[1] = (unsigned long)ct; ... While its very unlikely, its possible that ct == last. If this happens, then the refcount of ct was already incremented. This 2nd increment is never undone. This prevents the conntrack object from being released, which in turn keeps prevents cnet->count from dropping back to 0. This will then block the netns dismantle (or conntrack rmmod) as nf_conntrack_cleanup_net_list() will wait forever. This can be reproduced by running conntrack_resize.sh selftest in a loop. It takes ~20 minutes for me on a preemptible kernel on average before I see a runaway kworker spinning in nf_conntrack_cleanup_net_list. One fix would to change this to: if (res < 0) { if (ct != last) nf_conntrack_get(&ct->ct_general); But this reference counting isn_x27;t needed in the first place. We can just store a cookie value instead. A followup patch will do the same for ctnetlink_exp_dump_table, it looks to me as if this has the same problem and like ctnetlink_dump_table, we only need a _x27;skip hint_x27;, not the actual object so we can apply the same cookie strategy there as well. (CVE-2025-38721) In the Linux kernel, the following vulnerability has been resolved: media: imon: make send_packet() more robust syzbot is reporting that imon has three problems which result in hung tasks due to forever holding device lock [1]. First problem is that when usb_rx_callback_intf0() once got -EPROTO error after ictx->dev_present_intf0 became true, usb_rx_callback_intf0() resubmits urb after printk(), and resubmitted urb causes usb_rx_callback_intf0() to again get -EPROTO error. This results in printk() flooding (RCU stalls). Alan Stern commented [2] that In theory it_x27;s okay to resubmit _if_ the driver has a robust error-recovery scheme (such as giving up after some fixed limit on the number of errors or after some fixed time has elapsed, perhaps with a time delay to prevent a flood of errors). Most drivers don_x27;t bother to do this; they simply give up right away. This makes them more vulnerable to short-term noise interference during USB transfers, but in reality such interference is quite rare. There_x27;s nothing really wrong with giving up right away. but imon has a poor error-recovery scheme which just retries forever; this behavior should be fixed. Since I_x27;m not sure whether it is safe for imon users to give up upon any error code, this patch takes care of only union of error codes chosen from modules in drivers/media/rc/ directory which handle -EPROTO error (i.e. ir_toy, mceusb and igorplugusb). Second problem is that when usb_rx_callback_intf0() once got -EPROTO error before ictx->dev_present_intf0 becomes true, usb_rx_callback_intf0() always resubmits urb due to commit 8791d63af0cf ("[media] imon: don_x27;t wedge hardware after early callbacks"). Move the ictx->dev_present_intf0 test introduced by commit 6f6b90c9231a ("[media] imon: don_x27;t parse scancodes until intf configured") to immediately before imon_incoming_packet(), or the first problem explained above happens without printk() flooding (i.e. hung task). Third problem is that when usb_rx_callback_intf0() is not called for some reason (e.g. flaky hardware; the reproducer for this problem sometimes prevents usb_rx_callback_intf0() from being called), wait_for_completion_interruptible() in send_packet() never returns (i.e. hung task). As a workaround for such situation, change send_packet() to wait for completion with timeout of 10 seconds. (CVE-2025-68194) In the Linux kernel, the following vulnerability has been resolved: tls: Use __sk_dst_get() and dst_dev_rcu() in get_netdev_for_sock(). get_netdev_for_sock() is called during setsockopt(), so not under RCU. Using sk_dst_get(sk)->dev could trigger UAF. Let_x27;s use __sk_dst_get() and dst_dev_rcu(). Note that the only ->ndo_sk_get_lower_dev() user is bond_sk_get_lower_dev(), which uses RCU. (CVE-2025-40149) In the Linux kernel, the following vulnerability has been resolved: tipc: Fix use-after-free in tipc_mon_reinit_self(). syzbot reported use-after-free of tipc_net(net)->monitors[] in tipc_mon_reinit_self(). [0] The array is protected by RTNL, but tipc_mon_reinit_self() iterates over it without RTNL. tipc_mon_reinit_self() is called from tipc_net_finalize(), which is always under RTNL except for tipc_net_finalize_work(). Let_x27;s hold RTNL in tipc_net_finalize_work(). [0]: BUG: KASAN: slab-use-after-free in __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] BUG: KASAN: slab-use-after-free in _raw_spin_lock_irqsave+0xa7/0xf0 kernel/locking/spinlock.c:162 Read of size 1 at addr ffff88805eae1030 by task kworker/0:7/5989 CPU: 0 UID: 0 PID: 5989 Comm: kworker/0:7 Not tainted syzkaller #0 PREEMPT_{RT,(full)} Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/18/2025 Workqueue: events tipc_net_finalize_work Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x240 mm/kasan/report.c:482 kasan_report+0x118/0x150 mm/kasan/report.c:595 __kasan_check_byte+0x2a/0x40 mm/kasan/common.c:568 kasan_check_byte include/linux/kasan.h:399 [inline] lock_acquire+0x8d/0x360 kernel/locking/lockdep.c:5842 __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0xa7/0xf0 kernel/locking/spinlock.c:162 rtlock_slowlock kernel/locking/rtmutex.c:1894 [inline] rwbase_rtmutex_lock_state kernel/locking/spinlock_rt.c:160 [inline] rwbase_write_lock+0xd3/0x7e0 kernel/locking/rwbase_rt.c:244 rt_write_lock+0x76/0x110 kernel/locking/spinlock_rt.c:243 write_lock_bh include/linux/rwlock_rt.h:99 [inline] tipc_mon_reinit_self+0x79/0x430 net/tipc/monitor.c:718 tipc_net_finalize+0x115/0x190 net/tipc/net.c:140 process_one_work kernel/workqueue.c:3236 [inline] process_scheduled_works+0xade/0x17b0 kernel/workqueue.c:3319 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3400 kthread+0x70e/0x8a0 kernel/kthread.c:463 ret_from_fork+0x439/0x7d0 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> Allocated by task 6089: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:388 [inline] __kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:405 kasan_kmalloc include/linux/kasan.h:260 [inline] __kmalloc_cache_noprof+0x1a8/0x320 mm/slub.c:4407 kmalloc_noprof include/linux/slab.h:905 [inline] kzalloc_noprof include/linux/slab.h:1039 [inline] tipc_mon_create+0xc3/0x4d0 net/tipc/monitor.c:657 tipc_enable_bearer net/tipc/bearer.c:357 [inline] __tipc_nl_bearer_enable+0xe16/0x13f0 net/tipc/bearer.c:1047 __tipc_nl_compat_doit net/tipc/netlink_compat.c:371 [inline] tipc_nl_compat_doit+0x3bc/0x5f0 net/tipc/netlink_compat.c:393 tipc_nl_compat_handle net/tipc/netlink_compat.c:-1 [inline] tipc_nl_compat_recv+0x83c/0xbe0 net/tipc/netlink_compat.c:1321 genl_family_rcv_msg_doit+0x215/0x300 net/netlink/genetlink.c:1115 genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0x60e/0x790 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x208/0x470 net/netlink/af_netlink.c:2552 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1320 [inline] netlink_unicast+0x846/0xa10 net/netlink/af_netlink.c:1346 netlink_sendmsg+0x805/0xb30 net/netlink/af_netlink.c:1896 sock_sendmsg_nosec net/socket.c:714 [inline] __sock_sendmsg+0x21c/0x270 net/socket.c:729 ____sys_sendmsg+0x508/0x820 net/socket.c:2614 ___sys_sendmsg+0x21f/0x2a0 net/socket.c:2668 __sys_sendmsg net/socket.c:2700 [inline] __do_sys_sendmsg net/socket.c:2705 [inline] __se_sys_sendmsg net/socket.c:2703 [inline] __x64_sys_sendmsg+0x1a1/0x260 net/socket.c:2703 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0x3b0 arch/ ---truncated--- (CVE-2025-40280) In the Linux kernel, the following vulnerability has been resolved: binfmt_misc: restore write access before closing files opened by open_exec() bm_register_write() opens an executable file using open_exec(), which internally calls do_open_execat() and denies write access on the file to avoid modification while it is being executed. However, when an error occurs, bm_register_write() closes the file using filp_close() directly. This does not restore the write permission, which may cause subsequent write operations on the same file to fail. Fix this by calling exe_file_allow_write_access() before filp_close() to restore the write permission properly. (CVE-2025-68239) In the Linux kernel, the following vulnerability has been resolved: bpf, ktls: Fix data corruption when using bpf_msg_pop_data() in ktls When sending plaintext data, we initially calculated the corresponding ciphertext length. However, if we later reduced the plaintext data length via socket policy, we failed to recalculate the ciphertext length. This results in transmitting buffers containing uninitialized data during ciphertext transmission. This causes uninitialized bytes to be appended after a complete "Application Data" packet, leading to errors on the receiving end when parsing TLS record. (CVE-2025-38608) In the Linux kernel, the following vulnerability has been resolved: ipv6: use RCU in ip6_xmit() Use RCU in ip6_xmit() in order to use dst_dev_rcu() to prevent possible UAF. (CVE-2025-40135) In the Linux kernel, the following vulnerability has been resolved: nvme-multipath: fix lockdep WARN due to partition scan work Blktests test cases nvme/014, 057 and 058 fail occasionally due to a lockdep WARN. As reported in the Closes tag URL, the WARN indicates that a deadlock can happen due to the dependency among disk->open_mutex, kblockd workqueue completion and partition_scan_work completion. To avoid the lockdep WARN and the potential deadlock, cut the dependency by running the partition_scan_work not by kblockd workqueue but by nvme_wq. (CVE-2025-68218) In the Linux kernel, the following vulnerability has been resolved: smb: client: fix memory leak in cifs_construct_tcon() When having a multiuser mount with domain= specified and using cifscreds, cifs_set_cifscreds() will end up setting @ctx->domainname, so it needs to be freed before leaving cifs_construct_tcon(). This fixes the following memory leak reported by kmemleak: mount.cifs //srv/share /mnt -o domain=ZELDA,multiuser,... su - testuser cifscreds add -d ZELDA -u testuser ... ls /mnt/1 ... umount /mnt echo scan > /sys/kernel/debug/kmemleak cat /sys/kernel/debug/kmemleak unreferenced object 0xffff8881203c3f08 (size 8): comm "ls", pid 5060, jiffies 4307222943 hex dump (first 8 bytes): 5a 45 4c 44 41 00 cc cc ZELDA... backtrace (crc d109a8cf): __kmalloc_node_track_caller_noprof+0x572/0x710 kstrdup+0x3a/0x70 cifs_sb_tlink+0x1209/0x1770 [cifs] cifs_get_fattr+0xe1/0xf50 [cifs] cifs_get_inode_info+0xb5/0x240 [cifs] cifs_revalidate_dentry_attr+0x2d1/0x470 [cifs] cifs_getattr+0x28e/0x450 [cifs] vfs_getattr_nosec+0x126/0x180 vfs_statx+0xf6/0x220 do_statx+0xab/0x110 __x64_sys_statx+0xd5/0x130 do_syscall_64+0xbb/0x380 entry_SYSCALL_64_after_hwframe+0x77/0x7f (CVE-2025-68295) In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Clear cmds after chip reset Commit aefed3e5548f ("scsi: qla2xxx: target: Fix offline port handling and host reset handling") caused two problems: 1. Commands sent to FW, after chip reset got stuck and never freed as FW is not going to respond to them anymore. 2. BUG_ON(cmd->sg_mapped) in qlt_free_cmd(). Commit 26f9ce53817a ("scsi: qla2xxx: Fix missed DMA unmap for aborted commands") attempted to fix this, but introduced another bug under different circumstances when two different CPUs were racing to call qlt_unmap_sg() at the same time: BUG_ON(!valid_dma_direction(dir)) in dma_unmap_sg_attrs(). So revert "scsi: qla2xxx: Fix missed DMA unmap for aborted commands" and partially revert "scsi: qla2xxx: target: Fix offline port handling and host reset handling" at __qla2x00_abort_all_cmds. (CVE-2025-68745) In the Linux kernel, the following vulnerability has been resolved: usb: early: xhci-dbc: Fix a potential out-of-bound memory access If xdbc_bulk_write() fails, the values in _x27;buf_x27; can be anything. So the string is not guaranteed to be NULL terminated when xdbc_trace() is called. Reserve an extra byte, which will be zeroed automatically because _x27;buf_x27; is a static variable, in order to avoid troubles, should it happen. (CVE-2023-53840) In the Linux kernel, the following vulnerability has been resolved: net: use dst_dev_rcu() in sk_setup_caps() Use RCU to protect accesses to dst->dev from sk_setup_caps() and sk_dst_gso_max_size(). Also use dst_dev_rcu() in ip6_dst_mtu_maybe_forward(), and ip_dst_mtu_maybe_forward(). ip4_dst_hoplimit() can use dst_dev_net_rcu(). (CVE-2025-40170) In the Linux kernel, the following vulnerability has been resolved: smb: client: Fix refcount leak for cifs_sb_tlink Fix three refcount inconsistency issues related to `cifs_sb_tlink`. Comments for `cifs_sb_tlink` state that `cifs_put_tlink()` needs to be called after successful calls to `cifs_sb_tlink()`. Three calls fail to update refcount accordingly, leading to possible resource leaks. (CVE-2025-40103) In the Linux kernel, the following vulnerability has been resolved: net: qlogic/qede: fix potential out-of-bounds read in qede_tpa_cont() and qede_tpa_end() The loops in _x27;qede_tpa_cont()_x27; and _x27;qede_tpa_end()_x27;, iterate over _x27;cqe->len_list[]_x27; using only a zero-length terminator as the stopping condition. If the terminator was missing or malformed, the loop could run past the end of the fixed-size array. Add an explicit bound check using ARRAY_SIZE() in both loops to prevent a potential out-of-bounds access. Found by Linux Verification Center (linuxtesting.org) with SVACE. (CVE-2025-40252) In the Linux kernel, the following vulnerability has been resolved: net: dlink: handle copy_thresh allocation failure The driver did not handle failure of `netdev_alloc_skb_ip_align()`. If the allocation failed, dereferencing `skb->protocol` could lead to a NULL pointer dereference. This patch tries to allocate `skb`. If the allocation fails, it falls back to the normal path. Tested-on: D-Link DGE-550T Rev-A3 (CVE-2025-40053) In the Linux kernel, the following vulnerability has been resolved: nvmet-fc: move lsop put work to nvmet_fc_ls_req_op It_x27;s possible for more than one async command to be in flight from __nvmet_fc_send_ls_req. For each command, a tgtport reference is taken. In the current code, only one put work item is queued at a time, which results in a leaked reference. To fix this, move the work item to the nvmet_fc_ls_req_op struct, which already tracks all resources related to the command. (CVE-2025-40171) In the Linux kernel, the following vulnerability has been resolved: sctp: prevent possible shift-out-of-bounds in sctp_transport_update_rto syzbot reported a possible shift-out-of-bounds [1] Blamed commit added rto_alpha_max and rto_beta_max set to 1000. It is unclear if some sctp users are setting very large rto_alpha and/or rto_beta. In order to prevent user regression, perform the test at run time. Also add READ_ONCE() annotations as sysctl values can change under us. [1] UBSAN: shift-out-of-bounds in net/sctp/transport.c:509:41 shift exponent 64 is too large for 32-bit type _x27;unsigned int_x27; CPU: 0 UID: 0 PID: 16704 Comm: syz.2.2320 Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x16c/0x1f0 lib/dump_stack.c:120 ubsan_epilogue lib/ubsan.c:233 [inline] __ubsan_handle_shift_out_of_bounds+0x27f/0x420 lib/ubsan.c:494 sctp_transport_update_rto.cold+0x1c/0x34b net/sctp/transport.c:509 sctp_check_transmitted+0x11c4/0x1c30 net/sctp/outqueue.c:1502 sctp_outq_sack+0x4ef/0x1b20 net/sctp/outqueue.c:1338 sctp_cmd_process_sack net/sctp/sm_sideeffect.c:840 [inline] sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1372 [inline] (CVE-2025-40281) In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: remove never-working support for setting nsh fields The validation of the set(nsh(...)) action is completely wrong. It runs through the nsh_key_put_from_nlattr() function that is the same function that validates NSH keys for the flow match and the push_nsh() action. However, the set(nsh(...)) has a very different memory layout. Nested attributes in there are doubled in size in case of the masked set(). That makes proper validation impossible. There is also confusion in the code between the _x27;masked_x27; flag, that says that the nested attributes are doubled in size containing both the value and the mask, and the _x27;is_mask_x27; that says that the value we_x27;re parsing is the mask. This is causing kernel crash on trying to write into mask part of the match with SW_FLOW_KEY_PUT() during validation, while validate_nsh() doesn_x27;t allocate any memory for it: BUG: kernel NULL pointer dereference, address: 0000000000000018 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 1c2383067 P4D 1c2383067 PUD 20b703067 PMD 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 8 UID: 0 Kdump: loaded Not tainted 6.17.0-rc4+ #107 PREEMPT(voluntary) RIP: 0010:nsh_key_put_from_nlattr+0x19d/0x610 [openvswitch] Call Trace: <TASK> validate_nsh+0x60/0x90 [openvswitch] validate_set.constprop.0+0x270/0x3c0 [openvswitch] __ovs_nla_copy_actions+0x477/0x860 [openvswitch] ovs_nla_copy_actions+0x8d/0x100 [openvswitch] ovs_packet_cmd_execute+0x1cc/0x310 [openvswitch] genl_family_rcv_msg_doit+0xdb/0x130 genl_family_rcv_msg+0x14b/0x220 genl_rcv_msg+0x47/0xa0 netlink_rcv_skb+0x53/0x100 genl_rcv+0x24/0x40 netlink_unicast+0x280/0x3b0 netlink_sendmsg+0x1f7/0x430 ____sys_sendmsg+0x36b/0x3a0 ___sys_sendmsg+0x87/0xd0 __sys_sendmsg+0x6d/0xd0 do_syscall_64+0x7b/0x2c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e The third issue with this process is that while trying to convert the non-masked set into masked one, validate_set() copies and doubles the size of the OVS_KEY_ATTR_NSH as if it didn_x27;t have any nested attributes. It should be copying each nested attribute and doubling them in size independently. And the process must be properly reversed during the conversion back from masked to a non-masked variant during the flow dump. In the end, the only two outcomes of trying to use this action are either validation failure or a kernel crash. And if somehow someone manages to install a flow with such an action, it will most definitely not do what it is supposed to, since all the keys and the masks are mixed up. Fixing all the issues is a complex task as it requires re-writing most of the validation code. Given that and the fact that this functionality never worked since introduction, let_x27;s just remove it altogether. It_x27;s better to re-introduce it later with a proper implementation instead of trying to fix it in stable releases. (CVE-2025-40254) In the Linux kernel, the following vulnerability has been resolved: ipv6: reject malicious packets in ipv6_gso_segment() syzbot was able to craft a packet with very long IPv6 extension headers leading to an overflow of skb->transport_header. This 16bit field has a limited range. Add skb_reset_transport_header_careful() helper and use it from ipv6_gso_segment() WARNING: CPU: 0 PID: 5871 at ./include/linux/skbuff.h:3032 skb_reset_transport_header include/linux/skbuff.h:3032 [inline] WARNING: CPU: 0 PID: 5871 at ./include/linux/skbuff.h:3032 ipv6_gso_segment+0x15e2/0x21e0 net/ipv6/ip6_offload.c:151 Modules linked in: CPU: 0 UID: 0 PID: 5871 Comm: syz-executor211 Not tainted 6.16.0-rc6-syzkaller-g7abc678e3084 #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025 RIP: 0010:skb_reset_transport_header include/linux/skbuff.h:3032 [inline] RIP: 0010:ipv6_gso_segment+0x15e2/0x21e0 net/ipv6/ip6_offload.c:151 Call Trace: <TASK> skb_mac_gso_segment+0x31c/0x640 net/core/gso.c:53 nsh_gso_segment+0x54a/0xe10 net/nsh/nsh.c:110 skb_mac_gso_segment+0x31c/0x640 net/core/gso.c:53 __skb_gso_segment+0x342/0x510 net/core/gso.c:124 skb_gso_segment include/net/gso.h:83 [inline] validate_xmit_skb+0x857/0x11b0 net/core/dev.c:3950 validate_xmit_skb_list+0x84/0x120 net/core/dev.c:4000 sch_direct_xmit+0xd3/0x4b0 net/sched/sch_generic.c:329 __dev_xmit_skb net/core/dev.c:4102 [inline] __dev_queue_xmit+0x17b6/0x3a70 net/core/dev.c:4679 (CVE-2025-38572) In the Linux kernel, the following vulnerability has been resolved: cifs: fix session state check in reconnect to avoid use-after-free issue Don_x27;t collect exiting session in smb2_reconnect_server(), because it will be released soon. Note that the exiting session will stay in server->smb_ses_list until it complete the cifs_free_ipc() and logoff() and then delete itself from the list. (CVE-2023-53794) In the Linux kernel, the following vulnerability has been resolved: bpf: Add preempt_count_{sub,add} into btf id deny list The recursion check in __bpf_prog_enter* and __bpf_prog_exit* leave preempt_count_{sub,add} unprotected. When attaching trampoline to them we get panic as follows, [ 867.843050] BUG: TASK stack guard page was hit at 0000000009d325cf (stack is 0000000046a46a15..00000000537e7b28) [ 867.843064] stack guard page: 0000 [#1] PREEMPT SMP NOPTI [ 867.843067] CPU: 8 PID: 11009 Comm: trace Kdump: loaded Not tainted 6.2.0+ #4 [ 867.843100] Call Trace: [ 867.843101] <TASK> [ 867.843104] asm_exc_int3+0x3a/0x40 [ 867.843108] RIP: 0010:preempt_count_sub+0x1/0xa0 [ 867.843135] __bpf_prog_enter_recur+0x17/0x90 [ 867.843148] bpf_trampoline_6442468108_0+0x2e/0x1000 [ 867.843154] ? preempt_count_sub+0x1/0xa0 [ 867.843157] preempt_count_sub+0x5/0xa0 [ 867.843159] ? migrate_enable+0xac/0xf0 [ 867.843164] __bpf_prog_exit_recur+0x2d/0x40 [ 867.843168] bpf_trampoline_6442468108_0+0x55/0x1000 ... [ 867.843788] preempt_count_sub+0x5/0xa0 [ 867.843793] ? migrate_enable+0xac/0xf0 [ 867.843829] __bpf_prog_exit_recur+0x2d/0x40 [ 867.843837] BUG: IRQ stack guard page was hit at 0000000099bd8228 (stack is 00000000b23e2bc4..000000006d95af35) [ 867.843841] BUG: IRQ stack guard page was hit at 000000005ae07924 (stack is 00000000ffd69623..0000000014eb594c) [ 867.843843] BUG: IRQ stack guard page was hit at 00000000028320f0 (stack is 00000000034b6438..0000000078d1bcec) [ 867.843842] bpf_trampoline_6442468108_0+0x55/0x1000 ... That is because in __bpf_prog_exit_recur, the preempt_count_{sub,add} are called after prog->active is decreased. Fixing this by adding these two functions into btf ids deny list. (CVE-2023-54086) In the Linux kernel, the following vulnerability has been resolved: sctp: avoid NULL dereference when chunk data buffer is missing chunk->skb pointer is dereferenced in the if-block where it_x27;s supposed to be NULL only. chunk->skb can only be NULL if chunk->head_skb is not. Check for frag_list instead and do it just before replacing chunk->skb. We_x27;re sure that otherwise chunk->skb is non-NULL because of outer if() condition. (CVE-2025-40240) In the Linux kernel, the following vulnerability has been resolved: bpf: Fix metadata_dst leak __bpf_redirect_neigh_v{4,6} Cilium has a BPF egress gateway feature which forces outgoing K8s Pod traffic to pass through dedicated egress gateways which then SNAT the traffic in order to interact with stable IPs outside the cluster. The traffic is directed to the gateway via vxlan tunnel in collect md mode. A recent BPF change utilized the bpf_redirect_neigh() helper to forward packets after the arrival and decap on vxlan, which turned out over time that the kmalloc-256 slab usage in kernel was ever-increasing. The issue was that vxlan allocates the metadata_dst object and attaches it through a fake dst entry to the skb. The latter was never released though given bpf_redirect_neigh() was merely setting the new dst entry via skb_dst_set() without dropping an existing one first. (CVE-2025-40183) In the Linux kernel, the following vulnerability has been resolved: udp_tunnel: use netdev_warn() instead of netdev_WARN() netdev_WARN() uses WARN/WARN_ON to print a backtrace along with file and line information. In this case, udp_tunnel_nic_register() returning an error is just a failed operation, not a kernel bug. udp_tunnel_nic_register() can fail due to a memory allocation failure (kzalloc() or udp_tunnel_nic_alloc()). This is a normal runtime error and not a kernel bug. Replace netdev_WARN() with netdev_warn() accordingly. (CVE-2025-68191) In the Linux kernel, the following vulnerability has been resolved: PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV Before disabling SR-IOV via config space accesses to the parent PF, sriov_disable() first removes the PCI devices representing the VFs. Since commit 9d16947b7583 ("PCI: Add global pci_lock_rescan_remove()") such removal operations are serialized against concurrent remove and rescan using the pci_rescan_remove_lock. No such locking was ever added in sriov_disable() however. In particular when commit 18f9e9d150fc ("PCI/IOV: Factor out sriov_add_vfs()") factored out the PCI device removal into sriov_del_vfs() there was still no locking around the pci_iov_remove_virtfn() calls. On s390 the lack of serialization in sriov_disable() may cause double remove and list corruption with the below (amended) trace being observed: PSW: 0704c00180000000 0000000c914e4b38 (klist_put+56) GPRS: 000003800313fb48 0000000000000000 0000000100000001 0000000000000001 00000000f9b520a8 0000000000000000 0000000000002fbd 00000000f4cc9480 0000000000000001 0000000000000000 0000000000000000 0000000180692828 00000000818e8000 000003800313fe2c 000003800313fb20 000003800313fad8 #0 [3800313fb20] device_del at c9158ad5c #1 [3800313fb88] pci_remove_bus_device at c915105ba #2 [3800313fbd0] pci_iov_remove_virtfn at c9152f198 #3 [3800313fc28] zpci_iov_remove_virtfn at c90fb67c0 #4 [3800313fc60] zpci_bus_remove_device at c90fb6104 #5 [3800313fca0] __zpci_event_availability at c90fb3dca #6 [3800313fd08] chsc_process_sei_nt0 at c918fe4a2 #7 [3800313fd60] crw_collect_info at c91905822 #8 [3800313fe10] kthread at c90feb390 #9 [3800313fe68] __ret_from_fork at c90f6aa64 #10 [3800313fe98] ret_from_fork at c9194f3f2. This is because in addition to sriov_disable() removing the VFs, the platform also generates hot-unplug events for the VFs. This being the reverse operation to the hotplug events generated by sriov_enable() and handled via pdev->no_vf_scan. And while the event processing takes pci_rescan_remove_lock and checks whether the struct pci_dev still exists, the lack of synchronization makes this checking racy. Other races may also be possible of course though given that this lack of locking persisted so long observable races seem very rare. Even on s390 the list corruption was only observed with certain devices since the platform events are only triggered by config accesses after the removal, so as long as the removal finished synchronously they would not race. Either way the locking is missing so fix this by adding it to the sriov_del_vfs() helper. Just like PCI rescan-remove, locking is also missing in sriov_add_vfs() including for the error case where pci_stop_and_remove_bus_device() is called without the PCI rescan-remove lock being held. Even in the non-error case, adding new PCI devices and buses should be serialized via the PCI rescan-remove lock. Add the necessary locking. (CVE-2025-40219) In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Fix Use-after-free in validation Nodes stored in the validation duplicates hashtable come from an arena allocator that is cleared at the end of vmw_execbuf_process. All nodes are expected to be cleared in vmw_validation_drop_ht but this node escaped because its resource was destroyed prematurely. (CVE-2025-40111) In the Linux kernel, the following vulnerability has been resolved: fbcon: Set fb_display[i]->mode to NULL when the mode is released Recently, we discovered the following issue through syzkaller: BUG: KASAN: slab-use-after-free in fb_mode_is_equal+0x285/0x2f0 Read of size 4 at addr ff11000001b3c69c by task syz.xxx ... Call Trace: <TASK> dump_stack_lvl+0xab/0xe0 print_address_description.constprop.0+0x2c/0x390 print_report+0xb9/0x280 kasan_report+0xb8/0xf0 fb_mode_is_equal+0x285/0x2f0 fbcon_mode_deleted+0x129/0x180 fb_set_var+0xe7f/0x11d0 do_fb_ioctl+0x6a0/0x750 fb_ioctl+0xe0/0x140 __x64_sys_ioctl+0x193/0x210 do_syscall_64+0x5f/0x9c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Based on experimentation and analysis, during framebuffer unregistration, only the memory of fb_info->modelist is freed, without setting the corresponding fb_display[i]->mode to NULL for the freed modes. This leads to UAF issues during subsequent accesses. Here_x27;s an example of reproduction steps: 1. With /dev/fb0 already registered in the system, load a kernel module to register a new device /dev/fb1; 2. Set fb1_x27;s mode to the global fb_display[] array (via FBIOPUT_CON2FBMAP); 3. Switch console from fb to VGA (to allow normal rmmod of the ko); 4. Unload the kernel module, at this point fb1_x27;s modelist is freed, leaving a wild pointer in fb_display[]; 5. Trigger the bug via system calls through fb0 attempting to delete a mode from fb0. Add a check in do_unregister_framebuffer(): if the mode to be freed exists in fb_display[], set the corresponding mode pointer to NULL. (CVE-2025-40323) In the Linux kernel, the following vulnerability has been resolved: tcp_bpf: Call sk_msg_free() when tcp_bpf_send_verdict() fails to allocate psock->cork. syzbot reported the splat below. [0] The repro does the following: 1. Load a sk_msg prog that calls bpf_msg_cork_bytes(msg, cork_bytes) 2. Attach the prog to a SOCKMAP 3. Add a socket to the SOCKMAP 4. Activate fault injection 5. Send data less than cork_bytes At 5., the data is carried over to the next sendmsg() as it is smaller than the cork_bytes specified by bpf_msg_cork_bytes(). Then, tcp_bpf_send_verdict() tries to allocate psock->cork to hold the data, but this fails silently due to fault injection + __GFP_NOWARN. If the allocation fails, we need to revert the sk->sk_forward_alloc change done by sk_msg_alloc(). Let_x27;s call sk_msg_free() when tcp_bpf_send_verdict fails to allocate psock->cork. The "*copied" also needs to be updated such that a proper error can be returned to the caller, sendmsg. It fails to allocate psock->cork. Nothing has been corked so far, so this patch simply sets "*copied" to 0. [0]: WARNING: net/ipv4/af_inet.c:156 at inet_sock_destruct+0x623/0x730 net/ipv4/af_inet.c:156, CPU#1: syz-executor/5983 Modules linked in: CPU: 1 UID: 0 PID: 5983 Comm: syz-executor Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025 RIP: 0010:inet_sock_destruct+0x623/0x730 net/ipv4/af_inet.c:156 Code: 0f 0b 90 e9 62 fe ff ff e8 7a db b5 f7 90 0f 0b 90 e9 95 fe ff ff e8 6c db b5 f7 90 0f 0b 90 e9 bb fe ff ff e8 5e db b5 f7 90 <0f> 0b 90 e9 e1 fe ff ff 89 f9 80 e1 07 80 c1 03 38 c1 0f 8c 9f fc RSP: 0018:ffffc90000a08b48 EFLAGS: 00010246 RAX: ffffffff8a09d0b2 RBX: dffffc0000000000 RCX: ffff888024a23c80 RDX: 0000000000000100 RSI: 0000000000000fff RDI: 0000000000000000 RBP: 0000000000000fff R08: ffff88807e07c627 R09: 1ffff1100fc0f8c4 R10: dffffc0000000000 R11: ffffed100fc0f8c5 R12: ffff88807e07c380 R13: dffffc0000000000 R14: ffff88807e07c60c R15: 1ffff1100fc0f872 FS: 00005555604c4500(0000) GS:ffff888125af1000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005555604df5c8 CR3: 0000000032b06000 CR4: 00000000003526f0 Call Trace: <IRQ> __sk_destruct+0x86/0x660 net/core/sock.c:2339 rcu_do_batch kernel/rcu/tree.c:2605 [inline] rcu_core+0xca8/0x1770 kernel/rcu/tree.c:2861 handle_softirqs+0x286/0x870 kernel/softirq.c:579 __do_softirq kernel/softirq.c:613 [inline] invoke_softirq kernel/softirq.c:453 [inline] __irq_exit_rcu+0xca/0x1f0 kernel/softirq.c:680 irq_exit_rcu+0x9/0x30 kernel/softirq.c:696 instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1052 [inline] sysvec_apic_timer_interrupt+0xa6/0xc0 arch/x86/kernel/apic/apic.c:1052 </IRQ> (CVE-2025-39913) In the Linux kernel, the following vulnerability has been resolved: ceph: fix potential use-after-free bug when trimming caps When trimming the caps and just after the _x27;session->s_cap_lock_x27; is released in ceph_iterate_session_caps() the cap maybe removed by another thread, and when using the stale cap memory in the callbacks it will trigger use-after-free crash. We need to check the existence of the cap just after the _x27;ci->i_ceph_lock_x27; being acquired. And do nothing if it_x27;s already removed. (CVE-2023-53867) In the Linux kernel, the following vulnerability has been resolved: arch_topology: Fix incorrect error check in topology_parse_cpu_capacity() Fix incorrect use of PTR_ERR_OR_ZERO() in topology_parse_cpu_capacity() which causes the code to proceed with NULL clock pointers. The current logic uses !PTR_ERR_OR_ZERO(cpu_clk) which evaluates to true for both valid pointers and NULL, leading to potential NULL pointer dereference in clk_get_rate(). Per include/linux/err.h documentation, PTR_ERR_OR_ZERO(ptr) returns: "The error code within @ptr if it is an error pointer; 0 otherwise." This means PTR_ERR_OR_ZERO() returns 0 for both valid pointers AND NULL pointers. Therefore !PTR_ERR_OR_ZERO(cpu_clk) evaluates to true (proceed) when cpu_clk is either valid or NULL, causing clk_get_rate(NULL) to be called when of_clk_get() returns NULL. Replace with !IS_ERR_OR_NULL(cpu_clk) which only proceeds for valid pointers, preventing potential NULL pointer dereference in clk_get_rate(). (CVE-2025-40346) In the Linux kernel, the following vulnerability has been resolved: net: gso: Forbid IPv6 TSO with extensions on devices with only IPV6_CSUM When performing Generic Segmentation Offload (GSO) on an IPv6 packet that contains extension headers, the kernel incorrectly requests checksum offload if the egress device only advertises NETIF_F_IPV6_CSUM feature, which has a strict contract: it supports checksum offload only for plain TCP or UDP over IPv6 and explicitly does not support packets with extension headers. The current GSO logic violates this contract by failing to disable the feature for packets with extension headers, such as those used in GREoIPv6 tunnels. This violation results in the device being asked to perform an operation it cannot support, leading to a `skb_warn_bad_offload` warning and a collapse of network throughput. While device TSO/USO is correctly bypassed in favor of software GSO for these packets, the GSO stack must be explicitly told not to request checksum offload. Mask NETIF_F_IPV6_CSUM, NETIF_F_TSO6 and NETIF_F_GSO_UDP_L4 in gso_features_check if the IPv6 header contains extension headers to compute checksum in software. The exception is a BIG TCP extension, which, as stated in commit 68e068cabd2c6c53 ("net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets"): "The feature is only enabled on devices that support BIG TCP TSO. The header is only present for PF_PACKET taps like tcpdump, and not transmitted by physical devices." kernel log output (truncated): WARNING: CPU: 1 PID: 5273 at net/core/dev.c:3535 skb_warn_bad_offload+0x81/0x140 ... Call Trace: <TASK> skb_checksum_help+0x12a/0x1f0 validate_xmit_skb+0x1a3/0x2d0 validate_xmit_skb_list+0x4f/0x80 sch_direct_xmit+0x1a2/0x380 __dev_xmit_skb+0x242/0x670 __dev_queue_xmit+0x3fc/0x7f0 ip6_finish_output2+0x25e/0x5d0 ip6_finish_output+0x1fc/0x3f0 ip6_tnl_xmit+0x608/0xc00 [ip6_tunnel] ip6gre_tunnel_xmit+0x1c0/0x390 [ip6_gre] dev_hard_start_xmit+0x63/0x1c0 __dev_queue_xmit+0x6d0/0x7f0 ip6_finish_output2+0x214/0x5d0 ip6_finish_output+0x1fc/0x3f0 ip6_xmit+0x2ca/0x6f0 ip6_finish_output+0x1fc/0x3f0 ip6_xmit+0x2ca/0x6f0 inet6_csk_xmit+0xeb/0x150 __tcp_transmit_skb+0x555/0xa80 tcp_write_xmit+0x32a/0xe90 tcp_sendmsg_locked+0x437/0x1110 tcp_sendmsg+0x2f/0x50 ... skb linear: 00000000: e4 3d 1a 7d ec 30 e4 3d 1a 7e 5d 90 86 dd 60 0e skb linear: 00000010: 00 0a 1b 34 3c 40 20 11 00 00 00 00 00 00 00 00 skb linear: 00000020: 00 00 00 00 00 12 20 11 00 00 00 00 00 00 00 00 skb linear: 00000030: 00 00 00 00 00 11 2f 00 04 01 04 01 01 00 00 00 skb linear: 00000040: 86 dd 60 0e 00 0a 1b 00 06 40 20 23 00 00 00 00 skb linear: 00000050: 00 00 00 00 00 00 00 00 00 12 20 23 00 00 00 00 skb linear: 00000060: 00 00 00 00 00 00 00 00 00 11 bf 96 14 51 13 f9 skb linear: 00000070: ae 27 a0 a8 2b e3 80 18 00 40 5b 6f 00 00 01 01 skb linear: 00000080: 08 0a 42 d4 50 d5 4b 70 f8 1a (CVE-2025-39770) In the Linux kernel, the following vulnerability has been resolved: cifs: fix mid leak during reconnection after timeout threshold When the number of responses with status of STATUS_IO_TIMEOUT exceeds a specified threshold (NUM_STATUS_IO_TIMEOUT), we reconnect the connection. But we do not return the mid, or the credits returned for the mid, or reduce the number of in-flight requests. This bug could result in the server->in_flight count to go bad, and also cause a leak in the mids. This change moves the check to a few lines below where the response is decrypted, even of the response is read from the transform header. This way, the code for returning the mids can be reused. Also, the cifs_reconnect was reconnecting just the transport connection before. In case of multi-channel, this may not be what we want to do after several timeouts. Changed that to reconnect the session and the tree too. Also renamed NUM_STATUS_IO_TIMEOUT to a more appropriate name MAX_STATUS_IO_TIMEOUT. (CVE-2023-53597) In the Linux kernel, the following vulnerability has been resolved: fbdev: bitblit: bound-check glyph index in bit_putcs* bit_putcs_aligned()/unaligned() derived the glyph pointer from the character value masked by 0xff/0x1ff, which may exceed the actual font_x27;s glyph count and read past the end of the built-in font array. Clamp the index to the actual glyph count before computing the address. This fixes a global out-of-bounds read reported by syzbot. (CVE-2025-40322) In the Linux kernel, the following vulnerability has been resolved: dma-buf: insert memory barrier before updating num_fences smp_store_mb() inserts memory barrier after storing operation. It is different with what the comment is originally aiming so Null pointer dereference can be happened if memory update is reordered. (CVE-2025-38095) In the Linux kernel, the following vulnerability has been resolved: x86/CPU/AMD: Add RDSEED fix for Zen5 There_x27;s an issue with RDSEED_x27;s 16-bit and 32-bit register output variants on Zen5 which return a random value of 0 "at a rate inconsistent with randomness while incorrectly signaling success (CF=1)". Search the web for AMD-SB-7055 for more detail. Add a fix glue which checks microcode revisions. [ bp: Add microcode revisions checking, rewrite. ] (CVE-2025-68313) In the Linux kernel, the following vulnerability has been resolved: NFSD: free copynotify stateid in nfs4_free_ol_stateid() Typically copynotify stateid is freed either when parent_x27;s stateid is being close/freed or in nfsd4_laundromat if the stateid hasn_x27;t been used in a lease period. However, in case when the server got an OPEN (which created a parent stateid), followed by a COPY_NOTIFY using that stateid, followed by a client reboot. New client instance while doing CREATE_SESSION would force expire previous state of this client. It leads to the open state being freed thru release_openowner-> nfs4_free_ol_stateid() and it finds that it still has copynotify stateid associated with it. We currently print a warning and is triggerred WARNING: CPU: 1 PID: 8858 at fs/nfsd/nfs4state.c:1550 nfs4_free_ol_stateid+0xb0/0x100 [nfsd] This patch, instead, frees the associated copynotify stateid here. If the parent stateid is freed (without freeing the copynotify stateids associated with it), it leads to the list corruption when laundromat ends up freeing the copynotify state later. [ 1626.839430] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP [ 1626.842828] Modules linked in: nfnetlink_queue nfnetlink_log bluetooth cfg80211 rpcrdma rdma_cm iw_cm ib_cm ib_core nfsd nfs_acl lockd grace nfs_localio ext4 crc16 mbcache jbd2 overlay uinput snd_seq_dummy snd_hrtimer qrtr rfkill vfat fat uvcvideo snd_hda_codec_generic videobuf2_vmalloc videobuf2_memops snd_hda_intel uvc snd_intel_dspcfg videobuf2_v4l2 videobuf2_common snd_hda_codec snd_hda_core videodev snd_hwdep snd_seq mc snd_seq_device snd_pcm snd_timer snd soundcore sg loop auth_rpcgss vsock_loopback vmw_vsock_virtio_transport_common vmw_vsock_vmci_transport vmw_vmci vsock xfs 8021q garp stp llc mrp nvme ghash_ce e1000e nvme_core sr_mod nvme_keyring nvme_auth cdrom vmwgfx drm_ttm_helper ttm sunrpc dm_mirror dm_region_hash dm_log iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi fuse dm_multipath dm_mod nfnetlink [ 1626.855594] CPU: 2 UID: 0 PID: 199 Comm: kworker/u24:33 Kdump: loaded Tainted: G B W 6.17.0-rc7+ #22 PREEMPT(voluntary) [ 1626.857075] Tainted: [B]=BAD_PAGE, [W]=WARN [ 1626.857573] Hardware name: VMware, Inc. VMware20,1/VBSA, BIOS VMW201.00V.24006586.BA64.2406042154 06/04/2024 [ 1626.858724] Workqueue: nfsd4 laundromat_main [nfsd] [ 1626.859304] pstate: 61400005 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 1626.860010] pc : __list_del_entry_valid_or_report+0x148/0x200 [ 1626.860601] lr : __list_del_entry_valid_or_report+0x148/0x200 [ 1626.861182] sp : ffff8000881d7a40 [ 1626.861521] x29: ffff8000881d7a40 x28: 0000000000000018 x27: ffff0000c2a98200 [ 1626.862260] x26: 0000000000000600 x25: 0000000000000000 x24: ffff8000881d7b20 [ 1626.862986] x23: ffff0000c2a981e8 x22: 1fffe00012410e7d x21: ffff0000920873e8 [ 1626.863701] x20: ffff0000920873e8 x19: ffff000086f22998 x18: 0000000000000000 [ 1626.864421] x17: 20747562202c3839 x16: 3932326636383030 x15: 3030666666662065 [ 1626.865092] x14: 6220646c756f6873 x13: 0000000000000001 x12: ffff60004fd9e4a3 [ 1626.865713] x11: 1fffe0004fd9e4a2 x10: ffff60004fd9e4a2 x9 : dfff800000000000 [ 1626.866320] x8 : 00009fffb0261b5e x7 : ffff00027ecf2513 x6 : 0000000000000001 [ 1626.866938] x5 : ffff00027ecf2510 x4 : ffff60004fd9e4a3 x3 : 0000000000000000 [ 1626.867553] x2 : 0000000000000000 x1 : ffff000096069640 x0 : 000000000000006d [ 1626.868167] Call trace: [ 1626.868382] __list_del_entry_valid_or_report+0x148/0x200 (P) [ 1626.868876] _free_cpntf_state_locked+0xd0/0x268 [nfsd] [ 1626.869368] nfs4_laundromat+0x6f8/0x1058 [nfsd] [ 1626.869813] laundromat_main+0x24/0x60 [nfsd] [ 1626.870231] process_one_work+0x584/0x1050 [ 1626.870595] worker_thread+0x4c4/0xc60 [ 1626.870893] kthread+0x2f8/0x398 [ 1626.871146] ret_from_fork+0x10/0x20 [ 1626.871422] Code: aa1303e1 aa1403e3 910e8000 97bc55d7 (d4210000) [ 1626.871892] SMP: stopping secondary CPUs (CVE-2025-40273) In the Linux kernel, the following vulnerability has been resolved: xfrm: delete x->tunnel as we delete x The ipcomp fallback tunnels currently get deleted (from the various lists and hashtables) as the last user state that needed that fallback is destroyed (not deleted). If a reference to that user state still exists, the fallback state will remain on the hashtables/lists, triggering the WARN in xfrm_state_fini. Because of those remaining references, the fix in commit f75a2804da39 ("xfrm: destroy xfrm_state synchronously on net exit path") is not complete. We recently fixed one such situation in TCP due to defered freeing of skbs (commit 9b6412e6979f ("tcp: drop secpath at the same time as we currently drop dst")). This can also happen due to IP reassembly: skbs with a secpath remain on the reassembly queue until netns destruction. If we can_x27;t guarantee that the queues are flushed by the time xfrm_state_fini runs, there may still be references to a (user) xfrm_state, preventing the timely deletion of the corresponding fallback state. Instead of chasing each instance of skbs holding a secpath one by one, this patch fixes the issue directly within xfrm, by deleting the fallback state as soon as the last user state depending on it has been deleted. Destruction will still happen when the final reference is dropped. A separate lockdep class for the fallback state is required since we_x27;re going to lock x->tunnel while x is locked. (CVE-2025-40215) In the Linux kernel, the following vulnerability has been resolved: scsi: qla4xxx: Prevent a potential error pointer dereference The qla4xxx_get_ep_fwdb() function is supposed to return NULL on error, but qla4xxx_ep_connect() returns error pointers. Propagating the error pointers will lead to an Oops in the caller, so change the error pointers to NULL. (CVE-2025-39676) In the Linux kernel, the following vulnerability has been resolved: i40e: fix idx validation in i40e_validate_queue_map Ensure idx is within range of active/initialized TCs when iterating over vf->ch[idx] in i40e_validate_queue_map(). (CVE-2025-39972) In the Linux kernel, the following vulnerability has been resolved: bpf: Fix stackmap overflow check in __bpf_get_stackid() Syzkaller reported a KASAN slab-out-of-bounds write in __bpf_get_stackid() when copying stack trace data. The issue occurs when the perf trace contains more stack entries than the stack map bucket can hold, leading to an out-of-bounds write in the bucket_x27;s data array. (CVE-2025-68378) In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_router: Fix neighbour use-after-free We sometimes observe use-after-free when dereferencing a neighbour [1]. The problem seems to be that the driver stores a pointer to the neighbour, but without holding a reference on it. A reference is only taken when the neighbour is used by a nexthop. Fix by simplifying the reference counting scheme. Always take a reference when storing a neighbour pointer in a neighbour entry. Avoid taking a referencing when the neighbour is used by a nexthop as the neighbour entry associated with the nexthop already holds a reference. Tested by running the test that uncovered the problem over 300 times. Without this patch the problem was reproduced after a handful of iterations. [1] BUG: KASAN: slab-use-after-free in mlxsw_sp_neigh_entry_update+0x2d4/0x310 Read of size 8 at addr ffff88817f8e3420 by task ip/3929 CPU: 3 UID: 0 PID: 3929 Comm: ip Not tainted 6.18.0-rc4-virtme-g36b21a067510 #3 PREEMPT(full) Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023 Call Trace: <TASK> dump_stack_lvl+0x6f/0xa0 print_address_description.constprop.0+0x6e/0x300 print_report+0xfc/0x1fb kasan_report+0xe4/0x110 mlxsw_sp_neigh_entry_update+0x2d4/0x310 mlxsw_sp_router_rif_gone_sync+0x35f/0x510 mlxsw_sp_rif_destroy+0x1ea/0x730 mlxsw_sp_inetaddr_port_vlan_event+0xa1/0x1b0 __mlxsw_sp_inetaddr_lag_event+0xcc/0x130 __mlxsw_sp_inetaddr_event+0xf5/0x3c0 mlxsw_sp_router_netdevice_event+0x1015/0x1580 notifier_call_chain+0xcc/0x150 call_netdevice_notifiers_info+0x7e/0x100 __netdev_upper_dev_unlink+0x10b/0x210 netdev_upper_dev_unlink+0x79/0xa0 vrf_del_slave+0x18/0x50 do_set_master+0x146/0x7d0 do_setlink.isra.0+0x9a0/0x2880 rtnl_newlink+0x637/0xb20 rtnetlink_rcv_msg+0x6fe/0xb90 netlink_rcv_skb+0x123/0x380 netlink_unicast+0x4a3/0x770 netlink_sendmsg+0x75b/0xc90 __sock_sendmsg+0xbe/0x160 ____sys_sendmsg+0x5b2/0x7d0 ___sys_sendmsg+0xfd/0x180 __sys_sendmsg+0x124/0x1c0 do_syscall_64+0xbb/0xfd0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 [...] Allocated by task 109: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x7b/0x90 __kmalloc_noprof+0x2c1/0x790 neigh_alloc+0x6af/0x8f0 ___neigh_create+0x63/0xe90 mlxsw_sp_nexthop_neigh_init+0x430/0x7e0 mlxsw_sp_nexthop_type_init+0x212/0x960 mlxsw_sp_nexthop6_group_info_init.constprop.0+0x81f/0x1280 mlxsw_sp_nexthop6_group_get+0x392/0x6a0 mlxsw_sp_fib6_entry_create+0x46a/0xfd0 mlxsw_sp_router_fib6_replace+0x1ed/0x5f0 mlxsw_sp_router_fib6_event_work+0x10a/0x2a0 process_one_work+0xd57/0x1390 worker_thread+0x4d6/0xd40 kthread+0x355/0x5b0 ret_from_fork+0x1d4/0x270 ret_from_fork_asm+0x11/0x20 Freed by task 154: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x43/0x70 kmem_cache_free_bulk.part.0+0x1eb/0x5e0 kvfree_rcu_bulk+0x1f2/0x260 kfree_rcu_work+0x130/0x1b0 process_one_work+0xd57/0x1390 worker_thread+0x4d6/0xd40 kthread+0x355/0x5b0 ret_from_fork+0x1d4/0x270 ret_from_fork_asm+0x11/0x20 Last potentially related work creation: kasan_save_stack+0x30/0x50 kasan_record_aux_stack+0x8c/0xa0 kvfree_call_rcu+0x93/0x5b0 mlxsw_sp_router_neigh_event_work+0x67d/0x860 process_one_work+0xd57/0x1390 worker_thread+0x4d6/0xd40 kthread+0x355/0x5b0 ret_from_fork+0x1d4/0x270 ret_from_fork_asm+0x11/0x20 (CVE-2025-68801) In the Linux kernel, the following vulnerability has been resolved: HID: uclogic: Correct devm device reference for hidinput input_dev name Reference the HID device rather than the input device for the devm allocation of the input_dev name. Referencing the input_dev would lead to a use-after-free when the input_dev was unregistered and subsequently fires a uevent that depends on the name. At the point of firing the uevent, the name would be freed by devres management. Use devm_kasprintf to simplify the logic for allocating memory and formatting the input_dev name string. (CVE-2023-54207) In the Linux kernel, the following vulnerability has been resolved: bpf: Reject narrower access to pointer ctx fields The following BPF program, simplified from a syzkaller repro, causes a kernel warning: r0 = *(u8 *)(r1 + 169); exit; With pointer field sk being at offset 168 in __sk_buff. This access is detected as a narrower read in bpf_skb_is_valid_access because it doesn_x27;t match offsetof(struct __sk_buff, sk). It is therefore allowed and later proceeds to bpf_convert_ctx_access. Note that for the "is_narrower_load" case in the convert_ctx_accesses(), the insn->off is aligned, so the cnt may not be 0 because it matches the offsetof(struct __sk_buff, sk) in the bpf_convert_ctx_access. However, the target_size stays 0 and the verifier errors with a kernel warning: verifier bug: error during ctx access conversion(1) This patch fixes that to return a proper "invalid bpf_context access off=X size=Y" error on the load instruction. The same issue affects multiple other fields in context structures that allow narrow access. Some other non-affected fields (for sk_msg, sk_lookup, and sockopt) were also changed to use bpf_ctx_range_ptr for consistency. Note this syzkaller crash was reported in the "Closes" link below, which used to be about a different bug, fixed in commit fce7bd8e385a ("bpf/verifier: Handle BPF_LOAD_ACQ instructions in insn_def_regno()"). Because syzbot somehow confused the two bugs, the new crash and repro didn_x27;t get reported to the mailing list. (CVE-2025-38591) In the Linux kernel, the following vulnerability has been resolved: libceph: fix potential use-after-free in have_mon_and_osd_map() The wait loop in __ceph_open_session() can race with the client receiving a new monmap or osdmap shortly after the initial map is received. Both ceph_monc_handle_map() and handle_one_map() install a new map immediately after freeing the old one kfree(monc->monmap); monc->monmap = monmap; ceph_osdmap_destroy(osdc->osdmap); osdc->osdmap = newmap; under client->monc.mutex and client->osdc.lock respectively, but because neither is taken in have_mon_and_osd_map() it_x27;s possible for client->monc.monmap->epoch and client->osdc.osdmap->epoch arms in client->monc.monmap && client->monc.monmap->epoch && client->osdc.osdmap && client->osdc.osdmap->epoch; condition to dereference an already freed map. This happens to be reproducible with generic/395 and generic/397 with KASAN enabled: BUG: KASAN: slab-use-after-free in have_mon_and_osd_map+0x56/0x70 Read of size 4 at addr ffff88811012d810 by task mount.ceph/13305 CPU: 2 UID: 0 PID: 13305 Comm: mount.ceph Not tainted 6.14.0-rc2-build2+ #1266 ... Call Trace: <TASK> have_mon_and_osd_map+0x56/0x70 ceph_open_session+0x182/0x290 ceph_get_tree+0x333/0x680 vfs_get_tree+0x49/0x180 do_new_mount+0x1a3/0x2d0 path_mount+0x6dd/0x730 do_mount+0x99/0xe0 __do_sys_mount+0x141/0x180 do_syscall_64+0x9f/0x100 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> Allocated by task 13305: ceph_osdmap_alloc+0x16/0x130 ceph_osdc_init+0x27a/0x4c0 ceph_create_client+0x153/0x190 create_fs_client+0x50/0x2a0 ceph_get_tree+0xff/0x680 vfs_get_tree+0x49/0x180 do_new_mount+0x1a3/0x2d0 path_mount+0x6dd/0x730 do_mount+0x99/0xe0 __do_sys_mount+0x141/0x180 do_syscall_64+0x9f/0x100 entry_SYSCALL_64_after_hwframe+0x76/0x7e Freed by task 9475: kfree+0x212/0x290 handle_one_map+0x23c/0x3b0 ceph_osdc_handle_map+0x3c9/0x590 mon_dispatch+0x655/0x6f0 ceph_con_process_message+0xc3/0xe0 ceph_con_v1_try_read+0x614/0x760 ceph_con_workfn+0x2de/0x650 process_one_work+0x486/0x7c0 process_scheduled_works+0x73/0x90 worker_thread+0x1c8/0x2a0 kthread+0x2ec/0x300 ret_from_fork+0x24/0x40 ret_from_fork_asm+0x1a/0x30 Rewrite the wait loop to check the above condition directly with client->monc.mutex and client->osdc.lock taken as appropriate. While at it, improve the timeout handling (previously mount_timeout could be exceeded in case wait_event_interruptible_timeout() slept more than once) and access client->auth_err under client->monc.mutex to match how it_x27;s set in finish_auth(). monmap_show() and osdmap_show() now take the respective lock before accessing the map as well. (CVE-2025-68285) In the Linux kernel, the following vulnerability has been resolved: net: usb: Remove disruptive netif_wake_queue in rtl8150_set_multicast syzbot reported WARNING in rtl8150_start_xmit/usb_submit_urb. This is the sequence of events that leads to the warning: rtl8150_start_xmit() { netif_stop_queue(); usb_submit_urb(dev->tx_urb); } rtl8150_set_multicast() { netif_stop_queue(); netif_wake_queue(); <-- wakes up TX queue before URB is done } rtl8150_start_xmit() { netif_stop_queue(); usb_submit_urb(dev->tx_urb); <-- double submission } rtl8150_set_multicast being the ndo_set_rx_mode callback should not be calling netif_stop_queue and notif_start_queue as these handle TX queue synchronization. The net core function dev_set_rx_mode handles the synchronization for rtl8150_set_multicast making it safe to remove these locks. (CVE-2025-40140) In the Linux kernel, the following vulnerability has been resolved: be2net: pass wrb_params in case of OS2BMC be_insert_vlan_in_pkt() is called with the wrb_params argument being NULL at be_send_pkt_to_bmc() call site. This may lead to dereferencing a NULL pointer when processing a workaround for specific packet, as commit bc0c3405abbb ("be2net: fix a Tx stall bug caused by a specific ipv6 packet") states. The correct way would be to pass the wrb_params from be_xmit(). (CVE-2025-40264) Rejected reason: This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. (CVE-2025-40361) In the Linux kernel, the following vulnerability has been resolved: sctp: Fix MAC comparison to be constant-time To prevent timing attacks, MACs need to be compared in constant time. Use the appropriate helper function for this. (CVE-2025-40204) In the Linux kernel, the following vulnerability has been resolved: crypto: asymmetric_keys - prevent overflow in asymmetric_key_generate_id Use check_add_overflow() to guard against potential integer overflows when adding the binary blob lengths and the size of an asymmetric_key_id structure and return ERR_PTR(-EOVERFLOW) accordingly. This prevents a possible buffer overflow when copying data from potentially malicious X.509 certificate fields that can be arbitrarily large, such as ASN.1 INTEGER serial numbers, issuer names, etc. (CVE-2025-68724) Rejected reason: This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. (CVE-2025-39799) In the Linux kernel, the following vulnerability has been resolved: x86/fpu: Ensure XFD state on signal delivery Sean reported [1] the following splat when running KVM tests: WARNING: CPU: 232 PID: 15391 at xfd_validate_state+0x65/0x70 Call Trace: <TASK> fpu__clear_user_states+0x9c/0x100 arch_do_signal_or_restart+0x142/0x210 exit_to_user_mode_loop+0x55/0x100 do_syscall_64+0x205/0x2c0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Chao further identified [2] a reproducible scenario involving signal delivery: a non-AMX task is preempted by an AMX-enabled task which modifies the XFD MSR. When the non-AMX task resumes and reloads XSTATE with init values, a warning is triggered due to a mismatch between fpstate::xfd and the CPU_x27;s current XFD state. fpu__clear_user_states() does not currently re-synchronize the XFD state after such preemption. Invoke xfd_update_state() which detects and corrects the mismatch if there is a dynamic feature. This also benefits the sigreturn path, as fpu__restore_sig() may call fpu__clear_user_states() when the sigframe is inaccessible. [ dhansen: minor changelog munging ] (CVE-2025-68171) In the Linux kernel, the following vulnerability has been resolved: bpf: Do not let BPF test infra emit invalid GSO types to stack Yinhao et al. reported that their fuzzer tool was able to trigger a skb_warn_bad_offload() from netif_skb_features() -> gso_features_check(). When a BPF program - triggered via BPF test infra - pushes the packet to the loopback device via bpf_clone_redirect() then mentioned offload warning can be seen. GSO-related features are then rightfully disabled. We get into this situation due to convert___skb_to_skb() setting gso_segs and gso_size but not gso_type. Technically, it makes sense that this warning triggers since the GSO properties are malformed due to the gso_type. Potentially, the gso_type could be marked non-trustworthy through setting it at least to SKB_GSO_DODGY without any other specific assumptions, but that also feels wrong given we should not go further into the GSO engine in the first place. The checks were added in 121d57af308d ("gso: validate gso_type in GSO handlers") because there were malicious (syzbot) senders that combine a protocol with a non-matching gso_type. If we would want to drop such packets, gso_features_check() currently only returns feature flags via netif_skb_features(), so one location for potentially dropping such skbs could be validate_xmit_unreadable_skb(), but then otoh it would be an additional check in the fast-path for a very corner case. Given bpf_clone_redirect() is the only place where BPF test infra could emit such packets, lets reject them right there. (CVE-2025-68725) In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_ct: add seqadj extension for natted connections Sequence adjustment may be required for FTP traffic with PASV/EPSV modes. due to need to re-write packet payload (IP, port) on the ftp control connection. This can require changes to the TCP length and expected seq / ack_seq. The easiest way to reproduce this issue is with PASV mode. Example ruleset: table inet ftp_nat { ct helper ftp_helper { type "ftp" protocol tcp l3proto inet } chain prerouting { type filter hook prerouting priority 0; policy accept; tcp dport 21 ct state new ct helper set "ftp_helper" } } table ip nat { chain prerouting { type nat hook prerouting priority -100; policy accept; tcp dport 21 dnat ip prefix to ip daddr map { 192.168.100.1 : 192.168.13.2/32 } } chain postrouting { type nat hook postrouting priority 100 ; policy accept; tcp sport 21 snat ip prefix to ip saddr map { 192.168.13.2 : 192.168.100.1/32 } } } Note that the ftp helper gets assigned *after* the dnat setup. The inverse (nat after helper assign) is handled by an existing check in nf_nat_setup_info() and will not show the problem. Topoloy: +-------------------+ +----------------------------------+ | FTP: 192.168.13.2 | <-> | NAT: 192.168.13.3, 192.168.100.1 | +-------------------+ +----------------------------------+ | +-----------------------+ | Client: 192.168.100.2 | +-----------------------+ ftp nat changes do not work as expected in this case: Connected to 192.168.100.1. [..] ftp> epsv EPSV/EPRT on IPv4 off. ftp> ls 227 Entering passive mode (192,168,100,1,209,129). 421 Service not available, remote server has closed connection. Kernel logs: Missing nfct_seqadj_ext_add() setup call WARNING: CPU: 1 PID: 0 at net/netfilter/nf_conntrack_seqadj.c:41 [..] __nf_nat_mangle_tcp_packet+0x100/0x160 [nf_nat] nf_nat_ftp+0x142/0x280 [nf_nat_ftp] help+0x4d1/0x880 [nf_conntrack_ftp] nf_confirm+0x122/0x2e0 [nf_conntrack] nf_hook_slow+0x3c/0xb0 .. Fix this by adding the required extension when a conntrack helper is assigned to a connection that has a nat binding. (CVE-2025-68206) In the Linux kernel, the following vulnerability has been resolved: usb: storage: sddr55: Reject out-of-bound new_pba Discovered by Atuin - Automated Vulnerability Discovery Engine. new_pba comes from the status packet returned after each write. A bogus device could report values beyond the block count derived from info->capacity, letting the driver walk off the end of pba_to_lba[] and corrupt heap memory. Reject PBAs that exceed the computed block count and fail the transfer so we avoid touching out-of-range mapping entries. (CVE-2025-40345) In the Linux kernel, the following vulnerability has been resolved: bpf: Fix invalid prog->stats access when update_effective_progs fails Syzkaller triggers an invalid memory access issue following fault injection in update_effective_progs. The issue can be described as follows: __cgroup_bpf_detach update_effective_progs compute_effective_progs bpf_prog_array_alloc <-- fault inject purge_effective_progs /* change to dummy_bpf_prog */ array->items[index] = &dummy_bpf_prog.prog ---softirq start--- __do_softirq ... __cgroup_bpf_run_filter_skb __bpf_prog_run_save_cb bpf_prog_run stats = this_cpu_ptr(prog->stats) /* invalid memory access */ flags = u64_stats_update_begin_irqsave(&stats->syncp) ---softirq end--- static_branch_dec(&cgroup_bpf_enabled_key[atype]) The reason is that fault injection caused update_effective_progs to fail and then changed the original prog into dummy_bpf_prog.prog in purge_effective_progs. Then a softirq came, and accessing the members of dummy_bpf_prog.prog in the softirq triggers invalid mem access. To fix it, skip updating stats when stats is NULL. (CVE-2025-68742) In the Linux kernel, the following vulnerability has been resolved: iavf: use internal state to free traffic IRQs If the system tries to close the netdev while iavf_reset_task() is running, __LINK_STATE_START will be cleared and netif_running() will return false in iavf_reinit_interrupt_scheme(). This will result in iavf_free_traffic_irqs() not being called and a leak as follows: [7632.489326] remove_proc_entry: removing non-empty directory _x27;irq/999_x27;, leaking at least _x27;iavf-enp24s0f0v0-TxRx-0_x27; [7632.490214] WARNING: CPU: 0 PID: 10 at fs/proc/generic.c:718 remove_proc_entry+0x19b/0x1b0 is shown when pci_disable_msix() is later called. Fix by using the internal adapter state. The traffic IRQs will always exist if state == __IAVF_RUNNING. (CVE-2023-53850) In the Linux kernel, the following vulnerability has been resolved: ima: don_x27;t clear IMA_DIGSIG flag when setting or removing non-IMA xattr Currently when both IMA and EVM are in fix mode, the IMA signature will be reset to IMA hash if a program first stores IMA signature in security.ima and then writes/removes some other security xattr for the file. For example, on Fedora, after booting the kernel with "ima_appraise=fix evm=fix ima_policy=appraise_tcb" and installing rpm-plugin-ima, installing/reinstalling a package will not make good reference IMA signature generated. Instead IMA hash is generated, # getfattr -m - -d -e hex /usr/bin/bash # file: usr/bin/bash security.ima=0x0404... This happens because when setting security.selinux, the IMA_DIGSIG flag that had been set early was cleared. As a result, IMA hash is generated when the file is closed. Similarly, IMA signature can be cleared on file close after removing security xattr like security.evm or setting/removing ACL. Prevent replacing the IMA file signature with a file hash, by preventing the IMA_DIGSIG flag from being reset. Here_x27;s a minimal C reproducer which sets security.selinux as the last step which can also replaced by removing security.evm or setting ACL, #include <stdio.h> #include <sys/xattr.h> #include <fcntl.h> #include <unistd.h> #include <string.h> #include <stdlib.h> int main() { const char* file_path = "/usr/sbin/test_binary"; const char* hex_string = "030204d33204490066306402304"; int length = strlen(hex_string); char* ima_attr_value; int fd; fd = open(file_path, O_WRONLY|O_CREAT|O_EXCL, 0644); if (fd == -1) { perror("Error opening file"); return 1; } ima_attr_value = (char*)malloc(length / 2 ); for (int i = 0, j = 0; i < length; i += 2, j++) { sscanf(hex_string + i, "%2hhx", &ima_attr_value[j]); } if (fsetxattr(fd, "security.ima", ima_attr_value, length/2, 0) == -1) { perror("Error setting extended attribute"); close(fd); return 1; } const char* selinux_value= "system_u:object_r:bin_t:s0"; if (fsetxattr(fd, "security.selinux", selinux_value, strlen(selinux_value), 0) == -1) { perror("Error setting extended attribute"); close(fd); return 1; } close(fd); return 0; } (CVE-2025-68183) In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Validate command header size against SVGA_CMD_MAX_DATASIZE This data originates from userspace and is used in buffer offset calculations which could potentially overflow causing an out-of-bounds access. (CVE-2025-40277) In the Linux kernel, the following vulnerability has been resolved: jbd2: avoid bug_on in jbd2_journal_get_create_access() when file system corrupted There_x27;s issue when file system corrupted: ------------[ cut here ]------------ kernel BUG at fs/jbd2/transaction.c:1289! Oops: invalid opcode: 0000 [#1] SMP KASAN PTI CPU: 5 UID: 0 PID: 2031 Comm: mkdir Not tainted 6.18.0-rc1-next RIP: 0010:jbd2_journal_get_create_access+0x3b6/0x4d0 RSP: 0018:ffff888117aafa30 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff88811a86b000 RCX: ffffffff89a63534 RDX: 1ffff110200ec602 RSI: 0000000000000004 RDI: ffff888100763010 RBP: ffff888100763000 R08: 0000000000000001 R09: ffff888100763028 R10: 0000000000000003 R11: 0000000000000000 R12: 0000000000000000 R13: ffff88812c432000 R14: ffff88812c608000 R15: ffff888120bfc000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f91d6970c99 CR3: 00000001159c4000 CR4: 00000000000006f0 Call Trace: <TASK> __ext4_journal_get_create_access+0x42/0x170 ext4_getblk+0x319/0x6f0 ext4_bread+0x11/0x100 ext4_append+0x1e6/0x4a0 ext4_init_new_dir+0x145/0x1d0 ext4_mkdir+0x326/0x920 vfs_mkdir+0x45c/0x740 do_mkdirat+0x234/0x2f0 __x64_sys_mkdir+0xd6/0x120 do_syscall_64+0x5f/0xfa0 entry_SYSCALL_64_after_hwframe+0x76/0x7e The above issue occurs with us in errors=continue mode when accompanied by storage failures. There have been many inconsistencies in the file system data. In the case of file system data inconsistency, for example, if the block bitmap of a referenced block is not set, it can lead to the situation where a block being committed is allocated and used again. As a result, the following condition will not be satisfied then trigger BUG_ON. Of course, it is entirely possible to construct a problematic image that can trigger this BUG_ON through specific operations. In fact, I have constructed such an image and easily reproduced this issue. Therefore, J_ASSERT() holds true only under ideal conditions, but it may not necessarily be satisfied in exceptional scenarios. Using J_ASSERT() directly in abnormal situations would cause the system to crash, which is clearly not what we want. So here we directly trigger a JBD abort instead of immediately invoking BUG_ON. (CVE-2025-68337) In the Linux kernel, the following vulnerability has been resolved: netdevsim: fix memory leak in nsim_bus_dev_new() If device_register() failed in nsim_bus_dev_new(), the value of reference in nsim_bus_dev->dev is 1. obj->name in nsim_bus_dev->dev will not be released. unreferenced object 0xffff88810352c480 (size 16): comm "echo", pid 5691, jiffies 4294945921 (age 133.270s) hex dump (first 16 bytes): 6e 65 74 64 65 76 73 69 6d 31 00 00 00 00 00 00 netdevsim1...... backtrace: [<000000005e2e5e26>] __kmalloc_node_track_caller+0x3a/0xb0 [<0000000094ca4fc8>] kvasprintf+0xc3/0x160 [<00000000aad09bcc>] kvasprintf_const+0x55/0x180 [<000000009bac868d>] kobject_set_name_vargs+0x56/0x150 [<000000007c1a5d70>] dev_set_name+0xbb/0xf0 [<00000000ad0d126b>] device_add+0x1f8/0x1cb0 [<00000000c222ae24>] new_device_store+0x3b6/0x5e0 [<0000000043593421>] bus_attr_store+0x72/0xa0 [<00000000cbb1833a>] sysfs_kf_write+0x106/0x160 [<00000000d0dedb8a>] kernfs_fop_write_iter+0x3a8/0x5a0 [<00000000770b66e2>] vfs_write+0x8f0/0xc80 [<0000000078bb39be>] ksys_write+0x106/0x210 [<00000000005e55a4>] do_syscall_64+0x35/0x80 [<00000000eaa40bbc>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 (CVE-2022-50772) In the Linux kernel, the following vulnerability has been resolved: bpf: drop unnecessary user-triggerable WARN_ONCE in verifierl log It_x27;s trivial for user to trigger "verifier log line truncated" warning, as verifier has a fixed-sized buffer of 1024 bytes (as of now), and there are at least two pieces of user-provided information that can be output through this buffer, and both can be arbitrarily sized by user: - BTF names; - BTF.ext source code lines strings. Verifier log buffer should be properly sized for typical verifier state output. But it_x27;s sort-of expected that this buffer won_x27;t be long enough in some circumstances. So let_x27;s drop the check. In any case code will work correctly, at worst truncating a part of a single line output. (CVE-2023-54145) In the Linux kernel, the following vulnerability has been resolved: cifs: parse_dfs_referrals: prevent oob on malformed input Malicious SMB server can send invalid reply to FSCTL_DFS_GET_REFERRALS - reply smaller than sizeof(struct get_dfs_referral_rsp) - reply with number of referrals smaller than NumberOfReferrals in the header Processing of such replies will cause oob. Return -EINVAL error on such replies to prevent oob-s. (CVE-2025-40099) In the Linux kernel, the following vulnerability has been resolved: ACPI: video: Fix use-after-free in acpi_video_switch_brightness() The switch_brightness_work delayed work accesses device->brightness and device->backlight, freed by acpi_video_dev_unregister_backlight() during device removal. If the work executes after acpi_video_bus_unregister_backlight() frees these resources, it causes a use-after-free when acpi_video_switch_brightness() dereferences device->brightness or device->backlight. Fix this by calling cancel_delayed_work_sync() for each device_x27;s switch_brightness_work in acpi_video_bus_remove_notify_handler() after removing the notify handler that queues the work. This ensures the work completes before the memory is freed. [ rjw: Changelog edit ] (CVE-2025-40211) In the Linux kernel, the following vulnerability has been resolved: regulator: core: Protect regulator_supply_alias_list with regulator_list_mutex regulator_supply_alias_list was accessed without any locking in regulator_supply_alias(), regulator_register_supply_alias(), and regulator_unregister_supply_alias(). Concurrent registration, unregistration and lookups can race, leading to: 1 use-after-free if an alias entry is removed while being read, 2 duplicate entries when two threads register the same alias, 3 inconsistent alias mappings observed by consumers. Protect all traversals, insertions and deletions on regulator_supply_alias_list with the existing regulator_list_mutex. (CVE-2025-68354) In the Linux kernel, the following vulnerability has been resolved: PCI/AER: Fix NULL pointer access by aer_info The kzalloc(GFP_KERNEL) may return NULL, so all accesses to aer_info->xxx will result in kernel panic. Fix it. (CVE-2025-68309) In the Linux kernel, the following vulnerability has been resolved: mm/hugetlb: fix folio is still mapped when deleted Migration may be raced with fallocating hole. remove_inode_single_folio will unmap the folio if the folio is still mapped. However, it_x27;s called without folio lock. If the folio is migrated and the mapped pte has been converted to migration entry, folio_mapped() returns false, and won_x27;t unmap it. Due to extra refcount held by remove_inode_single_folio, migration fails, restores migration entry to normal pte, and the folio is mapped again. As a result, we triggered BUG in filemap_unaccount_folio. The log is as follows: BUG: Bad page cache in process hugetlb pfn:156c00 page: refcount:515 mapcount:0 mapping:0000000099fef6e1 index:0x0 pfn:0x156c00 head: order:9 mapcount:1 entire_mapcount:1 nr_pages_mapped:0 pincount:0 aops:hugetlbfs_aops ino:dcc dentry name(?):"my_hugepage_file" flags: 0x17ffffc00000c1(locked|waiters|head|node=0|zone=2|lastcpupid=0x1fffff) page_type: f4(hugetlb) page dumped because: still mapped when deleted CPU: 1 UID: 0 PID: 395 Comm: hugetlb Not tainted 6.17.0-rc5-00044-g7aac71907bde-dirty #484 NONE Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 0.0.0 02/06/2015 Call Trace: <TASK> dump_stack_lvl+0x4f/0x70 filemap_unaccount_folio+0xc4/0x1c0 __filemap_remove_folio+0x38/0x1c0 filemap_remove_folio+0x41/0xd0 remove_inode_hugepages+0x142/0x250 hugetlbfs_fallocate+0x471/0x5a0 vfs_fallocate+0x149/0x380 Hold folio lock before checking if the folio is mapped to avold race with migration. (CVE-2025-40006) In the Linux kernel, the following vulnerability has been resolved: sctp: initialize more fields in sctp_v6_from_sk() syzbot found that sin6_scope_id was not properly initialized, leading to undefined behavior. Clear sin6_scope_id and sin6_flowinfo. BUG: KMSAN: uninit-value in __sctp_v6_cmp_addr+0x887/0x8c0 net/sctp/ipv6.c:649 __sctp_v6_cmp_addr+0x887/0x8c0 net/sctp/ipv6.c:649 sctp_inet6_cmp_addr+0x4f2/0x510 net/sctp/ipv6.c:983 sctp_bind_addr_conflict+0x22a/0x3b0 net/sctp/bind_addr.c:390 sctp_get_port_local+0x21eb/0x2440 net/sctp/socket.c:8452 sctp_get_port net/sctp/socket.c:8523 [inline] sctp_listen_start net/sctp/socket.c:8567 [inline] sctp_inet_listen+0x710/0xfd0 net/sctp/socket.c:8636 __sys_listen_socket net/socket.c:1912 [inline] __sys_listen net/socket.c:1927 [inline] __do_sys_listen net/socket.c:1932 [inline] __se_sys_listen net/socket.c:1930 [inline] __x64_sys_listen+0x343/0x4c0 net/socket.c:1930 x64_sys_call+0x271d/0x3e20 arch/x86/include/generated/asm/syscalls_64.h:51 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xd9/0x210 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f Local variable addr.i.i created at: sctp_get_port net/sctp/socket.c:8515 [inline] sctp_listen_start net/sctp/socket.c:8567 [inline] sctp_inet_listen+0x650/0xfd0 net/sctp/socket.c:8636 __sys_listen_socket net/socket.c:1912 [inline] __sys_listen net/socket.c:1927 [inline] __do_sys_listen net/socket.c:1932 [inline] __se_sys_listen net/socket.c:1930 [inline] __x64_sys_listen+0x343/0x4c0 net/socket.c:1930 (CVE-2025-39812) In the Linux kernel, the following vulnerability has been resolved: NFSv4/pNFS: Clear NFS_INO_LAYOUTCOMMIT in pnfs_mark_layout_stateid_invalid Fixes a crash when layout is null during this call stack: write_inode -> nfs4_write_inode -> pnfs_layoutcommit_inode pnfs_set_layoutcommit relies on the lseg refcount to keep the layout around. Need to clear NFS_INO_LAYOUTCOMMIT otherwise we might attempt to reference a null layout. (CVE-2025-68349) In the Linux kernel, the following vulnerability has been resolved: media: b2c2: Fix use-after-free causing by irq_check_work in flexcop_pci_remove The original code uses cancel_delayed_work() in flexcop_pci_remove(), which does not guarantee that the delayed work item irq_check_work has fully completed if it was already running. This leads to use-after-free scenarios where flexcop_pci_remove() may free the flexcop_device while irq_check_work is still active and attempts to dereference the device. A typical race condition is illustrated below: CPU 0 (remove) | CPU 1 (delayed work callback) flexcop_pci_remove() | flexcop_pci_irq_check_work() cancel_delayed_work() | flexcop_device_kfree(fc_pci->fc_dev) | | fc = fc_pci->fc_dev; // UAF This is confirmed by a KASAN report: ================================================================== BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0 Write of size 8 at addr ffff8880093aa8c8 by task bash/135 ... Call Trace: <IRQ> dump_stack_lvl+0x55/0x70 print_report+0xcf/0x610 ? __run_timer_base.part.0+0x7d7/0x8c0 kasan_report+0xb8/0xf0 ? __run_timer_base.part.0+0x7d7/0x8c0 __run_timer_base.part.0+0x7d7/0x8c0 ? __pfx___run_timer_base.part.0+0x10/0x10 ? __pfx_read_tsc+0x10/0x10 ? ktime_get+0x60/0x140 ? lapic_next_event+0x11/0x20 ? clockevents_program_event+0x1d4/0x2a0 run_timer_softirq+0xd1/0x190 handle_softirqs+0x16a/0x550 irq_exit_rcu+0xaf/0xe0 sysvec_apic_timer_interrupt+0x70/0x80 </IRQ> ... Allocated by task 1: kasan_save_stack+0x24/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x7f/0x90 __kmalloc_noprof+0x1be/0x460 flexcop_device_kmalloc+0x54/0xe0 flexcop_pci_probe+0x1f/0x9d0 local_pci_probe+0xdc/0x190 pci_device_probe+0x2fe/0x470 really_probe+0x1ca/0x5c0 __driver_probe_device+0x248/0x310 driver_probe_device+0x44/0x120 __driver_attach+0xd2/0x310 bus_for_each_dev+0xed/0x170 bus_add_driver+0x208/0x500 driver_register+0x132/0x460 do_one_initcall+0x89/0x300 kernel_init_freeable+0x40d/0x720 kernel_init+0x1a/0x150 ret_from_fork+0x10c/0x1a0 ret_from_fork_asm+0x1a/0x30 Freed by task 135: kasan_save_stack+0x24/0x50 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3a/0x60 __kasan_slab_free+0x3f/0x50 kfree+0x137/0x370 flexcop_device_kfree+0x32/0x50 pci_device_remove+0xa6/0x1d0 device_release_driver_internal+0xf8/0x210 pci_stop_bus_device+0x105/0x150 pci_stop_and_remove_bus_device_locked+0x15/0x30 remove_store+0xcc/0xe0 kernfs_fop_write_iter+0x2c3/0x440 vfs_write+0x871/0xd70 ksys_write+0xee/0x1c0 do_syscall_64+0xac/0x280 entry_SYSCALL_64_after_hwframe+0x77/0x7f ... Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure that the delayed work item is properly canceled and any executing delayed work has finished before the device memory is deallocated. This bug was initially identified through static analysis. To reproduce and test it, I simulated the B2C2 FlexCop PCI device in QEMU and introduced artificial delays within the flexcop_pci_irq_check_work() function to increase the likelihood of triggering the bug. (CVE-2025-39996) In the Linux kernel, the following vulnerability has been resolved: KVM: x86: use array_index_nospec with indices that come from guest min and dest_id are guest-controlled indices. Using array_index_nospec() after the bounds checks clamps these values to mitigate speculative execution side-channels. (CVE-2025-39823) In the Linux kernel, the following vulnerability has been resolved: scsi: target: tcm_loop: Fix segfault in tcm_loop_tpg_address_show() If the allocation of tl_hba->sh fails in tcm_loop_driver_probe() and we attempt to dereference it in tcm_loop_tpg_address_show() we will get a segfault, see below for an example. So, check tl_hba->sh before dereferencing it. Unable to allocate struct scsi_host BUG: kernel NULL pointer dereference, address: 0000000000000194 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 1 PID: 8356 Comm: tokio-runtime-w Not tainted 6.6.104.2-4.azl3 #1 Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 09/28/2024 RIP: 0010:tcm_loop_tpg_address_show+0x2e/0x50 [tcm_loop] ... Call Trace: <TASK> configfs_read_iter+0x12d/0x1d0 [configfs] vfs_read+0x1b5/0x300 ksys_read+0x6f/0xf0 ... (CVE-2025-68229) In the Linux kernel, the following vulnerability has been resolved: media: rainshadow-cec: fix TOCTOU race condition in rain_interrupt() In the interrupt handler rain_interrupt(), the buffer full check on rain->buf_len is performed before acquiring rain->buf_lock. This creates a Time-of-Check to Time-of-Use (TOCTOU) race condition, as rain->buf_len is concurrently accessed and modified in the work handler rain_irq_work_handler() under the same lock. Multiple interrupt invocations can race, with each reading buf_len before it becomes full and then proceeding. This can lead to both interrupts attempting to write to the buffer, incrementing buf_len beyond its capacity (DATA_SIZE) and causing a buffer overflow. Fix this bug by moving the spin_lock() to before the buffer full check. This ensures that the check and the subsequent buffer modification are performed atomically, preventing the race condition. An corresponding spin_unlock() is added to the overflow path to correctly release the lock. This possible bug was found by an experimental static analysis tool developed by our team. (CVE-2025-39713) In the Linux kernel, the following vulnerability has been resolved: net: usb: qmi_wwan: initialize MAC header offset in qmimux_rx_fixup Raw IP packets have no MAC header, leaving skb->mac_header uninitialized. This can trigger kernel panics on ARM64 when xfrm or other subsystems access the offset due to strict alignment checks. Initialize the MAC header to prevent such crashes. This can trigger kernel panics on ARM when running IPsec over the qmimux0 interface. Example trace: Internal error: Oops: 000000009600004f [#1] SMP CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.34-gbe78e49cb433 #1 Hardware name: LS1028A RDB Board (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : xfrm_input+0xde8/0x1318 lr : xfrm_input+0x61c/0x1318 sp : ffff800080003b20 Call trace: xfrm_input+0xde8/0x1318 xfrm6_rcv+0x38/0x44 xfrm6_esp_rcv+0x48/0xa8 ip6_protocol_deliver_rcu+0x94/0x4b0 ip6_input_finish+0x44/0x70 ip6_input+0x44/0xc0 ipv6_rcv+0x6c/0x114 __netif_receive_skb_one_core+0x5c/0x8c __netif_receive_skb+0x18/0x60 process_backlog+0x78/0x17c __napi_poll+0x38/0x180 net_rx_action+0x168/0x2f0 (CVE-2025-68192) In the Linux kernel, the following vulnerability has been resolved: ARM: 9317/1: kexec: Make smp stop calls asynchronous If a panic is triggered by a hrtimer interrupt all online cpus will be notified and set offline. But as highlighted by commit 19dbdcb8039c ("smp: Warn on function calls from softirq context") this call should not be made synchronous with disabled interrupts: softdog: Initiating panic Kernel panic - not syncing: Software Watchdog Timer expired WARNING: CPU: 1 PID: 0 at kernel/smp.c:753 smp_call_function_many_cond unwind_backtrace: show_stack dump_stack_lvl __warn warn_slowpath_fmt smp_call_function_many_cond smp_call_function crash_smp_send_stop.part.0 machine_crash_shutdown __crash_kexec panic softdog_fire __hrtimer_run_queues hrtimer_interrupt Make the smp call for machine_crash_nonpanic_core() asynchronous. (CVE-2023-53712) In the Linux kernel, the following vulnerability has been resolved: nbd: defer config unlock in nbd_genl_connect There is one use-after-free warning when running NBD_CMD_CONNECT and NBD_CLEAR_SOCK: nbd_genl_connect nbd_alloc_and_init_config // config_refs=1 nbd_start_device // config_refs=2 set NBD_RT_HAS_CONFIG_REF open nbd // config_refs=3 recv_work done // config_refs=2 NBD_CLEAR_SOCK // config_refs=1 close nbd // config_refs=0 refcount_inc -> uaf ------------[ cut here ]------------ refcount_t: addition on 0; use-after-free. WARNING: CPU: 24 PID: 1014 at lib/refcount.c:25 refcount_warn_saturate+0x12e/0x290 nbd_genl_connect+0x16d0/0x1ab0 genl_family_rcv_msg_doit+0x1f3/0x310 genl_rcv_msg+0x44a/0x790 The issue can be easily reproduced by adding a small delay before refcount_inc(&nbd->config_refs) in nbd_genl_connect(): mutex_unlock(&nbd->config_lock); if (!ret) { set_bit(NBD_RT_HAS_CONFIG_REF, &config->runtime_flags); + printk("before sleep\n"); + mdelay(5 * 1000); + printk("after sleep\n"); refcount_inc(&nbd->config_refs); nbd_connect_reply(info, nbd->index); } (CVE-2025-68366) In the Linux kernel, the following vulnerability has been resolved: nvme-fc: use lock accessing port_state and rport state nvme_fc_unregister_remote removes the remote port on a lport object at any point in time when there is no active association. This races with with the reconnect logic, because nvme_fc_create_association is not taking a lock to check the port_state and atomically increase the active count on the rport. (CVE-2025-40342) In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_objref: validate objref and objrefmap expressions Referencing a synproxy stateful object from OUTPUT hook causes kernel crash due to infinite recursive calls: BUG: TASK stack guard page was hit at 000000008bda5b8c (stack is 000000003ab1c4a5..00000000494d8b12) [...] Call Trace: __find_rr_leaf+0x99/0x230 fib6_table_lookup+0x13b/0x2d0 ip6_pol_route+0xa4/0x400 fib6_rule_lookup+0x156/0x240 ip6_route_output_flags+0xc6/0x150 __nf_ip6_route+0x23/0x50 synproxy_send_tcp_ipv6+0x106/0x200 synproxy_send_client_synack_ipv6+0x1aa/0x1f0 nft_synproxy_do_eval+0x263/0x310 nft_do_chain+0x5a8/0x5f0 [nf_tables nft_do_chain_inet+0x98/0x110 nf_hook_slow+0x43/0xc0 __ip6_local_out+0xf0/0x170 ip6_local_out+0x17/0x70 synproxy_send_tcp_ipv6+0x1a2/0x200 synproxy_send_client_synack_ipv6+0x1aa/0x1f0 [...] Implement objref and objrefmap expression validate functions. Currently, only NFT_OBJECT_SYNPROXY object type requires validation. This will also handle a jump to a chain using a synproxy object from the OUTPUT hook. Now when trying to reference a synproxy object in the OUTPUT hook, nft will produce the following error: synproxy_crash.nft: Error: Could not process rule: Operation not supported synproxy name mysynproxy ^^^^^^^^^^^^^^^^^^^^^^^^ (CVE-2025-40206) In the Linux kernel, the following vulnerability has been resolved: vxlan: Annotate FDB data races The _x27;used_x27; and _x27;updated_x27; fields in the FDB entry structure can be accessed concurrently by multiple threads, leading to reports such as [1]. Can be reproduced using [2]. Suppress these reports by annotating these accesses using READ_ONCE() / WRITE_ONCE(). [1] BUG: KCSAN: data-race in vxlan_xmit / vxlan_xmit write to 0xffff942604d263a8 of 8 bytes by task 286 on cpu 0: vxlan_xmit+0xb29/0x2380 dev_hard_start_xmit+0x84/0x2f0 __dev_queue_xmit+0x45a/0x1650 packet_xmit+0x100/0x150 packet_sendmsg+0x2114/0x2ac0 __sys_sendto+0x318/0x330 __x64_sys_sendto+0x76/0x90 x64_sys_call+0x14e8/0x1c00 do_syscall_64+0x9e/0x1a0 entry_SYSCALL_64_after_hwframe+0x77/0x7f read to 0xffff942604d263a8 of 8 bytes by task 287 on cpu 2: vxlan_xmit+0xadf/0x2380 dev_hard_start_xmit+0x84/0x2f0 __dev_queue_xmit+0x45a/0x1650 packet_xmit+0x100/0x150 packet_sendmsg+0x2114/0x2ac0 __sys_sendto+0x318/0x330 __x64_sys_sendto+0x76/0x90 x64_sys_call+0x14e8/0x1c00 do_syscall_64+0x9e/0x1a0 entry_SYSCALL_64_after_hwframe+0x77/0x7f value changed: 0x00000000fffbac6e -> 0x00000000fffbac6f Reported by Kernel Concurrency Sanitizer on: CPU: 2 UID: 0 PID: 287 Comm: mausezahn Not tainted 6.13.0-rc7-01544-gb4b270f11a02 #5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014 [2] #!/bin/bash set +H echo whitelist > /sys/kernel/debug/kcsan echo !vxlan_xmit > /sys/kernel/debug/kcsan ip link add name vx0 up type vxlan id 10010 dstport 4789 local 192.0.2.1 bridge fdb add 00:11:22:33:44:55 dev vx0 self static dst 198.51.100.1 taskset -c 0 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q & taskset -c 2 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q & (CVE-2025-38037) HCE 2.0 bpftool-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm kernel-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm kernel-abi-stablelists-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm kernel-tools-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm kernel-tools-libs-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm kernel-tools-libs-devel-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm perf-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm python3-perf-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm bpftool-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm kernel-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm kernel-abi-stablelists-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm kernel-tools-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm kernel-tools-libs-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm kernel-tools-libs-devel-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm perf-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm python3-perf-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm kernel-devel-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm kernel-devel-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm kernel-headers-5.10.0-182.0.0.95.r3304_260.hce2.x86_64.rpm kernel-headers-5.10.0-182.0.0.95.r3304_260.hce2.aarch64.rpm